User manual ZOTAC ZBOX ID-81 PLUS

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - - - - REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. While every precaution has been taken in the preparation of this manual, no responsibility for errors or omissions is assumed. [. . . ] Before using your computer, make sure all jumpers and DRAM modules are set correctly. CMOS Clear Jumper-JP1 1 1 JP1 Selection 1-2* Normal* 2-3 CMOS Clear Keyboard Power Selection for Wakeup-JP2 1 1 JP2 1-2 2-3* Selection Power off in S3/S4/S5 Power on in any state* Case Open Jumper-JP5 JP5 Open Short Close Selection Case close Case open Open * = Default setting. If you want to clear the system configuration, use the JP1 (Clear CMOS Jumper) to clear data. If the CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. 16 Configuring the BIOS Configuring the BIOS Enter BIOS Setup This section discusses how to change the system settings through the BIOS Setup menus. Correctly setting the BIOS parameters is critical to maintain optimal system performance. 2. Press the Del key when the following message briefly displays at the bottom of the screen during the Power On Self Test (POST). We reserve the right to update the BIOS version presented in the manual. It is strongly recommended that you do not change the default BIOS settings. Changing some settings could damage your system. Main Menu This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. Note: Users please note that the data in gray is non-changeable, and the others are for selection. q BIOS Information Displays the auto-detected BIOS information. 17 Intel NM70-ITX series Motherboard q q q q Processor Information Displays the auto-detected processor information. System Date/Time Allows you to set the system date/time. Advanced Menu The Advanced menu items allow you to change the setting for the CPU and other system devices. Press <enter> to display the configuration options: ACPI Configuration The items in this menu allow you to set or change the ACPI configurations. q Aperture Size This item allows you to set the aperture size, options: 64MB/128MB/256MB. q DVMT Pre-Allocated This item allows you to set DVMT pre-allocated size. q DVMT Total Gfx Mem This item allows you to set DVMT total Gfx mem size. OnBoard Device Configuration The items allow you to configure onboard device, including HD Audio, LAN and so on. q LAN1/2 Controller Enable or disable onboard LAN1/2 controller. 20 Configuring the BIOS q USB 3. 0/2. 0 Controller Enable or disable USB 3. 0/2. 0 controller. q HD Audio Controller Enable or disable HD Audio controller. Network Stack The item in this menu allows you to set network stack. q Network stack This item allows you to enable or disable UEFI network stack. X-Setting Menu The X-Setting menu items show the settings of CPU, memory and so on. Press <enter> to display the configuration options: q Adjust Memory Voltage Use this item to adjust memory voltage. q Memory Frequency Limiter Use this item to adjust memory frequency. 21 Intel NM70-ITX series Motherboard Boot Menu The Boot menu items allow you to change the system boot options. Press <enter> to display the configuration options: Boot Configuration The items allow you to configure Boot settings. Press <enter> To display the configuration options: q Setup Prompt Timeout This item shows the number of seconds to wait for setup activation key. q Bootup NumLock State Use this item to select the keyboard NumLock state: [On] or [Off]. [. . . ] Warning: - Do not turn off or RESET the computer during the flash process. - If you are not sure how to upgrade the BIOS, please take your computer to an Authorized Service Center and have a trained technician do the work for you. 26 Installing Drivers And Software Installing Drivers and Software Note: 1. It is important to remember that before installing the driver disk that is shipped in the kit, you need to load your operating system. The motherboard supports Windows 7 32bit/64bit and Windows 8 32bit/64bit. [. . . ]