User manual ZOOM UIB-01

[. . . ] UIB-01 Installation Manual © Zoom Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited. Safety Precautions In this manual, important information that is intended to prevent the danger of injury to persons and damage to equipment is marked with special symbols. Disregarding instructions printed here incurs the risk of death or Warning severe injury to persons. Disregarding instructions printed here incurs the risk of injury to Caution persons and/or damage to peripheral equipment. Please observe the following safety tips and precautions to ensure hazard-free use of the UIB-01. [. . . ] (The actual drive letter may be different on your computer. ) · The volume label for the MRS-1044 recognized as local disk differs depending on the operating system. In Windows 98, the volume label is shown as "None" and in Windows Me and Windows 2000 as "Local Disk". · The driver installation process must only be carried out once. The next time you start up the MRS-1044 in USB mode, simply connect the USB cable between the MRS-1044 and the computer, and MRS-1044 and the computer will be automatically online. · When wishing to uninstall (delete) the driver, use the "UNINST" program on the supplied CD-ROM ( p. 30). Terminating the connection between computer and MRS-1044 If you unplug the USB cable or turn the MRS-1044 off while the computer and MRS-1044 are still in the online state, malfunction may occur and files may be damaged. To terminate the connection between the computer and the MRS-1044, always use the following steps. Preparations 1. Click on the "USB Storage Unplug" icon in the task tray, and select [Stop ZOOM USB-ATA/ATAPI Bridge Mass Storage Controller]. "USB Storage Unplug" is a program for setting the computer and MRS-1044 to the offline state. The icon for the program automatically appears in the task tray when the online state is established. * If no new local disk is shown p. 31 When the computer and MRS-1044 are in the online state, the following icon will be added to the task tray. 2. Click on the [OK] button in the dialog box that appears. This icon accesses the "USB Storage Unplug" program that serves to terminate the USB connection between MRS-1044 and computer. 18 ZOOM UIB-01 ZOOM UIB-01 19 UIB-01 Applications The computer and MRS-1044 are now in the offline state, and you can terminate the USB connection. In the offline state, the "USB Storage Unplug" icon should disappear from the task tray. If not, right-click on the icon and select [End of USB Storage Unplug]. This section describes the various uses of the UIB-01. Project backup/restore You can copy a project from the MRS-1044 recognized as a local disk to the hard disk of the computer, for creating a backup. A backed-up project can be restored to the MRS-1044 at any time. 3. Push the [POWER] switch of the MRS-1044. The indication "PowrOFF ENT/EXIT" appears on the display of the MRS-1044. When you turn the power on again in this state, the unit starts up normally. If necessary, disconnect the USB cable. This procedure must be followed every time you wish to terminate the USB connection between the computer and the MRS-1044 to turn the MRS-1044 off. Backing up a project 1. 4. Start up the MRS-1044 in USB mode and connect it to the computer with a USB cable. Open "My Computer" and double-click on the local disk representing the MRS-1044. Project data are stored separately in folders named "PROJxxx" (where "xxx" is the project number from 000 - 999). Preparations 2. UIB-01 Applications 5. NOTE Other folders and files are used by the system of the MRS-1044. 28. 20 ZOOM UIB-01 ZOOM UIB-01 21 3. Select the folder of the project you want to back up, and select [Copy] from the [Edit] menu on the menu bar. 3. Select the folder for the project you want to restore, and select [Copy] from the [Edit] menu on the menu bar. 4. Open the destination drive/folder and select [Paste] from the [Edit] menu on the menu bar. 4. 5. Open "My Computer" and double-click on the local disk representing the MRS-1044. Select [Paste] from the [Edit] menu on the menu bar. UIB-01 Applications UIB-01 Applications Backup of the project data is now complete. If necessary, back up other projects in the same way. Restoring a project You can restore projects backed up on the hard disk of the computer to the internal hard disk of the MRS-1044. The project is restored to the hard disk on the MRS-1044. If a folder with the same name as the folder selected for restore already exists on the hard disk of the MRS-1044, the following indication appears. 1. Start up the MRS-1044 in USB mode and connect it to the computer with a USB cable. Open the drive/folder where the project backup data are stored. 2. If you click on the [Yes to All] button, existing data on the hard disk of the MRS-1044 will be overwritten by the restored project data. (V-take files for which no restore data are present will remain unchanged. ) ZOOM UIB-01 22 ZOOM UIB-01 23 Returning the MRS-1044 to the factory default condition The supplied CD-ROM contains complete data about the factory default settings of the MRS-1044. [. . . ] (2) Track/V-take window : The track/V-take configuration of the currently selected project can be checked here. At V-take positions where audio data are recorded, a button with the name of the V-take is shown. (3) V-Take Wav button : Clicking on this button will cause the audio data of the V-take selected in the track/V-take window (2) to be exported to a WAV file (file extension: WAV). (4) Wav/AIFF V-Take button : Clicking on this button will cause the audio data of a WAV file (file extension: WAV) or AIFF file (file extension: AIF) to be imported to the V-take selected in the track/Vtake window (2). [. . . ]