User manual ZOOM R24

[. . . ] · Total of 16 effects (eight effect types per distortion module) can be combined . Besides distortion effects, PRE DRIVE also contains compressor, pedal wah, auto wah, octaver and other versatile effects. · You can switch between 24 patches to store diverse settings based on your preference. · Mixing balance of PRE DRIVE and MAIN DRIVE can be varied according to picking intensity, using the auto-parallel connection feature. [. . . ] (2) Parameter 4 (GAIN parameter of MAIN DRIVE) set to "Pd" : Pedal controls gain of MAIN DRIVE. (3) Parameter 9 (Serial/parallel switching) set to "Pd" : Pedal controls mixing balance of PRE DRIVE and MAIN DRIVE modules. * Functions (1) - (3) can be used simultaneously. For patches where (1) - (3) do not apply, the pedal serves as volume pedal to control the overall output level. DETECTOR IN For details, please refer to the operation manual of the DUAL POWER MODULATOR 509. OUTPUT jack This jack is for the output signal from the 510. When you change the setting, the display will show"tunEr oFF" (tuning function off) or "tunEr on" (tuning function on) according to the setting. A1 Calibration Select reference pitch for auto-chromatic guitar tuner (calibration). * The reference pitch (A) can be adjusted in the range from 435 to 445 Hz. When the BANK key is pressed in Bypass/Tuner mode, this is shown as "35" to "45" on the display for a second. At power-on, the setting is 440 Hz (40). Bypass mode Pressing both patch pedals simultaneously activates the Bypass mode. Currently selected patch is displayed Press both pedals together Bypass ON/OFF The bypass function is invoked by pressing the left and right patch pedals simultaneously. To cancel the Bypass/Tuner mode, just press one of the patch pedals. Press Release immediately Tuning function (only when the tuning function is ON) To cancel the Bypass mode, simply press one of the patch pedals. The unit then reverts to the previously selected patch. Tuner mode The 510 is initially set so that the auto-chromatic tuning function for the guitar activates automatically when the Bypass mode is invoked. The closest note will be shown on the display. Input signal standby condition Regular tuning Do = C Do# = C# Regular tuning Re# = D# Regular tuning Fa# = F# 6th string 1st string Regular tuning La = A 3rd string 5th string Mi = E 4th string So = G So# = G# La# = A# Regular tuning Re = D Fa = F Si = B 2nd string When the tuning function is active, the parameter cursor LEDs serve as tuning meter, designed to enhance tuning precision during fine adjustments. Turning tuning function off If you do not want to activate the tuning function in Bypass Pitch is too high Correctly tuned Pitch is too low mode, press the STORE and EDIT keys simultaneously for more than one second in Play mode. The tuning function will be turned off, and this setting will be stored even when the power is turned off. Each push of the EDIT key moves the blinking parameter cursor indicator one step down. The PATCH UP/DOWN pedals move the blinking parameter cursor indicator up or down. When the EDIT key is pressed while the lowest indicator (Parameter 8: LEVEL) is flashing, the TUNER indicator (Parameter 9: SERIAL/PARA) starts flashing. When the EDIT key is pressed while the TUNER indicator (Parameter 9: SERIAL/PARA) is selected, the Edit mode is terminated and the 510 reverts to the Play mode. PATCH UP moves the blinking parameter cursor one step up and PATCH DOWN moves it one step down. * When the PATCH DOWN pedal is pressed while the TUNER indicator (Parameter 9: SERIAL/PARA) is flashing, the 510 stays in Edit mode and parameter 1 is selected. 7 Sr A1 There are a total of eight indicators, assigned to parameters 1 ­ 8 from top to bottom, plus the TUNER indicator which is assigned to parameter 9. The parameter functions are as follows. · Parameter 1:PRE DRIVE (PRE DRIVE effect type selection) · Parameter 2:GAIN (PRE DRIVE parameter setting) · Parameter 3:MAIN DRIVE (MAIN DRIVE effect type selection) · Parameter 4:GAIN (MAIN DRIVE parameter setting) · Parameter 5:HIGH (High-range equalizer) · Parameter 6:LOW (Low-range equalizer) · Parameter 7:ZNR/AMP (ZNR setting/amp simulator on, off) · Parameter 8:LEVEL (Patch level) · Parameter 9:SERIAL/PARA (Serial/parallel connection) (1) Use the EDIT key or patch (2) Use the VALUE +/- keys pedal to select the parameter to adjust the parameter. (3) While the TUNER indicator (Parameter 9) is flashing, press the EDIT key to return to Play mode. *Use the VALUE +/- keys to change the setting of the parameter. For details on parameters, please refer to section 12 "Effect Parameters". 12 Effect Parameters PARAMETER 1 PRE DRIVE Selects the effect type to be used in the PRE DRIVE module. 8 different effect types are available. (PRE DRIVE effect type) Increases or decreases the setting by 1 effect type. + ­ 1 BOOSTER 2 RHYTHM 3 LIGHT OD 4 DYNAMIC OD 5 COMP (Compressor) Conventional compressor effect. 6 AUTO WAH Auto wah with changing characteristics depending on picking intensity. 7 PEDAL WAH Pedal wah for use with optional expression pedal FP01. The center frequency that is being emphasized goes up and down, depending on the pedal action. 8 OCTAVE Natural sounding octaver creating a sound one octave lower. For use with single notes only. VALUE +/- keys + ­ Setting range 1 ­ Increases the setting by 1 effect type. Creates a Light distortion (Light overdrive) (Dynamic overdrive) clean sound suitable for Light overdrive Dynamic overdrive effect with prominent rhythm guitar. [. . . ] This is activated in the Edit mode by pressing both VALUE keys together. For example, if GAIN (parameter 4) of the MAIN DRIVE module is set to "Pd" (pedal controls gain) and you want to change it to "12", you would have to press the VALUE + key 12 times. Instead, you can achieve the same effect by using the shortcut function: press the VALUE +/- keys together With the 510 you are also able to set the master level that governs the overall output level. While the level is being displayed, use the VALUE +/- keys to change it. [. . . ]