User manual ZOOM H4V2

[. . . ] 12 Display font change The size of the font used for the display has been increased. As a result, some effect type names and parameter names are now shown differently, as listed in the table below. ■ PRE AMP module effect type names Version 1. x Version 2. 0 BG CRUNCH TS+FD_CMB SD+MS_STK FZ+MS_STK SuperBass VO MICPRE AG MICPRE FLAT MPRE BGcrunch TS+FDcmb SD+MSstk FZ+MSstk SUP-BASS VO MPRE AG MPRE FlatMPRE ■ EFX module effect type names Version 1. x Version 2. 0 RACK COMP RVS DELAY RackComp RvsDelay ■ Effect parameter names Version 1. x Version 2. 0 THRESHOLD RESONANCE FREQUENCE PRE DELAY THRSHOLD RESONANC FREQ PRE DLY © Zoom Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited. H4 Version 2. 0 Supplemental Manual 1 H4SupM_E. fm 2 ページ ２００７年１０月１９日　金曜日　午前１０時３８分 H4 Version 2. 0 Supplemental Manual Support for SDHC cards In addition to regular SD cards, the H4 now also supports the high-capacity SDHC cards, increasing the maximum capacity from 2 to 4 GB. For information on supported cards, please visit the ZOOM Corporation web site (http:// www. zoom. co. jp). Due to this change, the available characters for file names and folder names are limited as follows: (space) ! [. . . ] Then press the jog dial. A screen for specifying the bit rate (amount of information per second of the MP3 file) and the file name appears. 1. At the stereo mode top screen, press the center of the [MENU] key. The main menu which gives access to various H4 settings appears. 5. To change the bit rate setting, move the jog dial up/down to bring the cursor to "BIT". Then press the jog dial. 2. Move the jog dial up/down to bring the cursor to "FILE". Move the jog dial up/down to select one of the following settings, and then press the jog dial. ● Available bit rate settings The FILE menu for selecting various operations for recorded files appears. 48, 56, 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps), VBR The higher the bit rate setting, the better the sound quality. With this setting, the bit rate adapts to the amount of information that is to be H4 Version 2. 0 Supplemental Manual 5 H4SupM_E. fm 6 ページ ２００７年１０月１９日　金曜日　午前１０時３８分 H4 Version 2. 0 Supplemental Manual encoded. This method makes it possible to achieve fairly small file sizes without excessive degradation of sound quality. Using the auto recording function (stereo mode only) The auto record function makes it possible to have the H4 start and stop recording automatically, according to the input signal level. When the level exceeds a certain threshold, recording starts, and when it remains below the threshold for a given length of time, recording stops. This is convenient to record only spoken comments at a meeting or interview or similar. To use the auto recording function, proceed as follows. 6. To change the file name, move the jog dial up/down to bring the cursor to "NAME". Then press the jog dial. The cursor disappears and a character is underlined. Specify the name, using the same procedure as described on page 47 of the H4 Operation Manual. 7. To carry out the MP3 file conversion, move the jog dial up/down to bring the cursor to "OK". Then press the jog dial. 1. The conversion process starts and the indication "Please Wait" appears. When the conversion is finished, the indication "Complete!" is shown, and the file selection screen of step 3 appears again. NOTE If a file with the same name already exists in the current project folder, the message "This file name already exists" appears. In this case, pressing the jog dial will cause the indication of step 6 to appear again. Change the file name and repeat the procedure. At the stereo mode top screen, press the center of the [MENU] key. The main menu which gives access to various H4 settings appears. 2. Move the jog dial up/down to bring the cursor to "AUTO RECORDING". Then press the jog dial. 8. To return to the stereo mode top screen, press the center of the [MENU] key repeatedly. The AUTO RECORDING screen for making settings for the function appears. Settings available from this screen are as follows. 6 H4 Version 2. 0 Supplemental Manual H4SupM_E. fm 7 ページ ２００７年１０月１９日　金曜日　午前１０時３８分 H4 Version 2. 0 Supplemental Manual ● START Turns the auto record function on. ● START LV (Start level) Sets the threshold level for automatically starting to record. ● STOP LVL (Stop level) A screen with an input signal level meter appears on the display. While watching the input signal level on the display, move the jog dial up/down to set the stop level to a suitable point. The AUTO RECORDING screen appears again. Sets the threshold level for automatically stopping to record. ● AUTO STP 5. Controls the auto stop on/off setting and the number of seconds until actual recording stops. When the signal drops below the specified stop level, recording will stop after the number of seconds set here. To enable the auto stop function, move the jog dial up/down to bring the cursor to "AUTO STP". The AUTO RECORDING screen appears again. Auto stop function is disabled (Recording must be stopped manually. ) Recording stops immediately when input signal level falls below stop level. Recording stops after 1 – 5 seconds when input signal level falls below stop level. 3. To set the start level, move the jog dial up/down to bring the cursor to "START LV". Then press the jog dial. 0FF 0sec 1 – 5sec A screen with an input signal level meter appears on the display. [. . . ] Then press the jog dial. The message "Are You Sure?" appears for confirmation. 1. At the stereo mode top screen, press the center of the [MENU] key. The main menu which gives access to various H4 settings appears. 5. Move the jog dial up/down to bring the cursor to "NORMALIZE". Then press the jog dial. During the normalizing operation, the indication H4 Version 2. 0 Supplemental Manual 11 H4SupM_E. fm 12 ページ ２００７年１０月１９日　金曜日　午前１０時３８分 H4 Version 2. 0 Supplemental Manual "Please Wait" is shown. When the operation is finished, the indication "Complete!" is shown, and the file selection screen of step 3 appears again. In this condition, you can select the input signal type. HINT If you move the cursor to "CANCEL" instead of "NORMALIZE" and press the jog dial, the operation is canceled and the screen of the preceding step appears again. NOTE While "INPUT" is set to "OFF", the "LEVEL" and "TUNER" setup screens cannot be selected. [. . . ]