User manual ZOOM GFX8
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ZOOM GFX8. We hope that this ZOOM GFX8 user guide will be useful to you.
You may also download the following manuals related to this product:
ZOOM GFX8 (1805 ko)
ZOOM GFX8 (1753 ko)
ZOOM GFX8 (1769 ko)
ZOOM GFX8 (1769 ko)
ZOOM GFX8 (1798 ko)
ZOOM GFX8 (1753 ko)
ZOOM GFX8 (1682 ko)
Manual abstract: user guide ZOOM GFX8
Detailed instructions for use are in the User's Guide.
[. . . ] Do not use abrasive cleanser, wax, or solvents (such as paint thinner or cleaning alcohol), since these may dull the finish or damage the surface.
⢠Power requirements
⢠The GFX-8 is powered by the supplied AC adapter . Warning ⢠To prevent malfunction and safety hazards, Do not use any other kind of AC adapter. ⢠When using the GFX-8 in an area with a different line voltage, please consult your local ZOOM distributor about acquiring a proper AC adapter. Please keep this manual in a convenient place for future reference.
⢠Environment
Avoid using your GFX-8 in environments where it will be
Caution exposed to:
⢠Extreme temperature ⢠High humidity or moisture ⢠Excessive dust or sand ⢠Excessive vibration or shock
⢠Handling
Since the GFX-8 is a precision electronic device, avoid Caution applying excessive force to the switches and buttons. [. . . ] For fine adjustment, use the PARM VALUE knob.
⢠So (SOUND ON SOUND) In this mode, the sampled sound is played back over the current sound. While the CONTROL switch is kept depressed, guitar play sound is added to the playback sound. The delay time set with parameter 1 + 2 determines the duration of the repeat interval. * The sampled data are retained until the module is set to OFF or the unit is set to the bypass condition.
Parameter 2
INTERVAL
t1 - t9
Parameter 4 Parameter 5
HOLD MIX
0 - 50
Adjusts the note that determines the delay sound timing, using the BPM tempo setting as reference. t1 = Two full notes t3 = quarter note t5 = half triplet note t7 = dotted sixteenth note t9 = sixteenth note t2 = dotted quarter note t4 = dotted eighth note t6 = eighth note t8 = quarter triplet note 0 - 50 0 - 50
Parameter 8
See TYPE 1A (CHORUS). Serves to start and stop the sampling process and to start playback.
Parameter 3 Parameter 4 Parameter 5
FEEDBACK BPM MIX
TYPE
10A
TRM+CHO
TRM DPT
This is a combination of tremolo and chorus.
Parameter 8
Parameter 1 Parameter 2
0 - 50
See TYPE 1A (CHORUS). Sets the delay time according to the interval in which the CONTROL switch is operated.
Effects and Parameters
Adjusts the tremolo effect depth.
TRM RATE
1 - 50
Adjusts the tremolo effect modulation rate.
Parameter 3
CHO RATE
1 - 50
TYPE
9B
HOLD DLY
Adjusts the chorus effect modulation rate.
This is a hold delay effect which can sample and playback a phrase of up to 6 seconds in length.
Parameter 4 Parameter 5
CHO MIX
0 - 50
Adjusts the chorus sound mix ratio.
Parameter 1 Parameter 2 Parameter 3
TIMEx100
0 - 60
Parameter 8
Sets delay time in 100-ms units .
TIMEx1
See TYPE 1A (CHORUS). tr, Gt, So
Sets delay time in 1-ms units.
MODE
Selects the hold mode. ⢠tr (TRIGGER) Sampling starts when the CONTROL switch is pressed. When the CONTROL switch is pressed once more, sampling stops and playback starts. If the CONTROL switch is not pressed twice, sampling automatically stops after the delay time has elapsed. Pressing the CONTROL switch once more stops playback.
Original sound Effect Sound
TYPE
10B
RING+VIB
VIB DPT
This is a combination of ring modulator and vibrato.
Parameter 1 Parameter 2 Parameter 3 Parameter 4
0 - 50
Adjusts the vibrato depth.
VIB RATE
1 - 50
Adjusts the vibrato rate.
RING SPD
1 - 50
Adjusts the modulation frequency of the ring modulator effect.
Sampling
Time
RING BAL
0 - 50
CONTROL switch Press Sampling start
Adjusts the ring modulator balance.
Press
Stop Playback
Press
Cancel hold
Parameter 5
Parameter 8
See TYPE 1A (CHORUS). ⢠Gt (GATE) Sampling is carried out while the CONTROL switch is being pressed. If the CONTROL switch is not released, sampling automatically stops after the delay time set with parameter 1 + 2 has elapsed, and playback starts. Switches the vibrato on and off.
TYPE TYPE
11A 11B
CUSTOM1 CUSTOM2
Original sound Effect Sound
Call up the previously stored custom settings 1/2 for the MOD module. (For information on creating and storing custom settings, see page 18. )
Sampling
Time
CONTROL switch Press Sampling start
Release
Playback
Press
End
The currently stored parameters can be edited. To retain any changes, store the patch.
24
ZOOM GFX-8
DLY/REV (Delay/Reverb) module
This module contains mainly single reverb type effects such as delay and reverb, but it also covers combinations with modulation effects and special effects and contains the jam effect making use of sampling technology.
Indicates a parameter that can be controlled by RTM (see page 30). Indicates a parameter for which tap input is possible with the CONTROL switch (see page 31). Indicates a parameter that can be controlled with the PARM VALUE knob during easy edit (see page 11). [CONTROL SW] indicates an item that can be operated with the CONTROL switch (see page 31).
* TYPE 2A and 2B have the same parameters.
TYPE TYPE
2A 2B
DLY+HALL DLY+ROOM
DLY TIME
This is a combination of delay and hall reverb.
This is a combination of delay and room reverb.
Parameter 1
1 - 99, 1. 0
Sets the delay time in 10-ms units (10 ms x setting value = delay time). Common Parameters of DLY/REV Module
RATE xx MIX BALANCE
Adjusts the modulation rate. "dn" means downward change, and "UP" upward change.
Parameter 2 Parameter 3 Parameter 4 Parameter 4 Parameter 5
DLY FB
0 - 50
Adjusts the amount of delay feedback.
DLY MIX
0 - 50
Adjusts the delay sound mix ratio.
HALL MIX ROOM MIX
FEEDBACK SHIFT
0 - 50 (when 2A is selected) 0 - 50 (when 2B is selected)
Adjusts the reverb sound mix ratio.
* TYPE 1A and 1B have the same parameters.
Parameter 8
Effects and Parameters
See TYPE 1A (REV HALL). [. . . ] URL: http://www. zoom. co. jp
MIDI Usage Examples
(2) Visual editor
Using knobs, switches and other graphical elements appearing on the computer screen, patches contained in project files can be edited. Because the edited contents are sent immediately to the GFX-8 via the MIDI link, the effect of any editing operation can be checked immediately by listening to the sound. Edited patches can be stored on the computer and can also be sent to the GFX-8 via the MIDI link.
40
ZOOM GFX-8
Other Functions
This section contains information about special functions such as how to return the GFX-8 to the factory default condition and how to readjust the expression pedal.
All Initialize/Factory Recall
The All Initialize/Factory Recall function is a special function that lets you reset the GFX-8 to the condition in which it was originally shipped. When All Initialize is performed, all settings of the unit including all user group patches are returned to the default condition. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ZOOM GFX8
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ZOOM GFX8 will begin.