User manual ZOOM 3000B

[. . . ] ADVANCED BASS EFFECTS PROCESSOR OPERATION MANUAL USAGE AND SAFETY PRECAUTIONS USAGE AND SAFETY PRECAUTIONS In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows: USAGE AND SAFETY PRECAUTIONS Warning This symbol indicates explanations about extremely dangerous matters. If users ignore this symbol and handle the device the wrong way, serious injury or death could result. If users ignore this symbol and handle the device the wrong way, bodily injury and damage to the equipment could result. Caution Please observe the following safety tips and precautions to ensure hazard-free use of the 3000B. · Power requirements Warning The 3000B is powered by the supplied AC adapter. [. . . ] The maximum delay time is 1000 ms when the effect type is DELAY and 500 ms when the effect type is DLY+REV. [ Tap input steps ] FUNCTION LED flash lit flash Step on Function switch twice delay time TIME NOTE · Delay time tap input can be performed in Play mode or Edit mode. In either mode, the delay time setting will be lost when the unit is turned off, unless the patch was stored. · If the optional remote pedal RP01 is connected and set to DELAY mode, delay time tap input is possible only with the foot switch of the remote pedal RP01 (page 38). q 26 ADVANCED BASS EFFECTS PROCESSOR Adjusting Effect Parameters in Real Time (RTM) When the FUNCTION Mode is set to "9: RTM", the so-called RTM (real-time modulation) function can be used. RTM allows the user to change effect parameters in real time, using the FUNCTION switch. To use RTM, the reference setting (before change by RTM) and the maximum or minimum value (after change by RTM) must be set for each effect module. POSITION FUNCTION MODE BANK(VALUE) COMP 1. COMP2. COMP2 3. LIMITER 4. DUAL COMP 5. DEFRET 6. SLAP Sens/Sens 1 Atk/Sens 2 Peak/X-F Tone/Bal Level VOLUME RTM DIST/AMP WAH EQ 1. GRAPHIC 2. 3-BAND 3. PARAMETRIC 8kHz/High/F1 4kHz/MidF/G1 2kHz/MidG/F2 1kHz/Low/G2 Level ZNR SYNTH EFFECT DLY/REV 1. CLN1 2. CLN2 1. AUTO 2. PEDAL 3. TE-C 4. SW-C 3. OCT 4. PHASE 5. OD 6. FUZZ 5. ENH 6. P-EQ 7. FN-D 8. AC-D 7. GRAPHIC EQ Gain/Mid Enh Level D. Level Cabinet 1:DIST-WAH 2:WAH-DIST DIST/AMP RTM Dpt/F1/500Hz Spd/G1/250Hz Color/F2/100Hz Mode/G2/500Hz Level WAH RTM 1-6. BASS SYNTH 1. CHO 2. FLG 1. DELAY 4. P-PIT 2. HALL 3. ROOM 7. HARMO SYNTH 3. PIT 5. DETUNE 6. TRILL 4. EARLY REF 7. SWEEP 8. RING 5. DLY+REV Freq/Mode Reso/Scale Decay/Atk D. Level Level SYNTH RTM Color/Pit/Dly Dpt/Sft/Mode Rate/Tone Mix/Bal/Reso FUNCTION Mode EFFECT RTM DlyTime/RevTime FineTime/DlyMix FB/RevColor DlyMix/RevMix Patch Level DLY/REV RTM 1. BANK DOWN 2. MANUAL 3. HOLD DLY(LONG) 4. HOLD DLY(REAL) 5. DELAY(TAP) METRO TEMPO 6. BYPASS 7. MUTE 9. RTM USER METRO VOL METRO ON/OFF U UO PRESET (BOTH) BANK FUNCTION 1, 9 11, 12 3, 5, 7 3, 4, 6 2 INPUT ATT MASTER HIGH MASTER MID EDIT(CANCEL) GROUP STORE MASTER LOW VALUE ADVANCED BASS EFFECTS PROCESSOR STEP 1 Press the EDIT key to activate the Edit mode. EDIT(CANCEL) Using the FUNCTION switch STEP 2 Use the Module Select keys to choose the module to be controlled by RTM. If the module is off, press the Module Select key once more to turn it on. NOTE Effect parameters of the COMP module and EQ module cannot be controlled by RTM. STEP 3 Use the Parameter Select keys and the VALUE knob to choose the effect type. METRO ON/OFF METRO TEMPO METRO VOL VALUE STEP 4 Use the Parameter Select keys to choose the effect parameter to be controlled by RTM. Which parameter can be controlled depends on the effect type. In the "Effect Types and Parameters" table on page 40­52, the parameter ADVANCED BASS EFFECTS PROCESSOR 27 q marked with " RTM" can be controlled by RTM. For example, when the effect type CHO is selected for the EFFECT module, the "Mix" parameter can be controlled by RTM. STEP 5 Use the VALUE knob to adjust the value of the effect parameter. VALUE The value set in this way becomes the reference setting for RTM. STEP 6 Use the Parameter Select keys to choose parameter 6. MASTER MID MASTER LOW For every effect module except for the COMP module and EQ module, parameter 6 is the RTM parameter which determines the maximum (or minimum) value that is reached by RTM control. STEP 7 Use the VALUE knob to adjust the RTM parameter. VALUE For example, if the "Mix" parameter was set to "50" in step 5, and the RTM parameter is "0", the adjustment range is 0 - 50. When the parameter is "100", the adjustment range is 50 - 100. When the RTM parameter is "oF", RTM control cannot be used for that module. Using the FUNCTION switch NOTE Depending on the effect type, the RTM parameter causes a change in the upward or downward direction. For details, please refer to "Effect Types and Parameters" (pages 40­52). STEP 8 9 If desired, repeat steps 2 through 7 to make the RTM setting for other effect modules. When the setting is completed, press the EDIT key to revert to Play mode. EDIT(CANCEL) STEP If necessary, store the patch as described on page 19. The RTM setting can be stored individually for each patch. STEP 10 Set the FUNCTION Mode to "9: RTM". For details, please refer to page 21. STEP 11 While playing your instrument, press and hold the FUNCTION switch. The value of the effect parameter selected in step 5 changes gradually towards the maximum (minimum) value set in step 7, causing a change in the sound quality of the patch. When the maximum (minimum) value is reached, the parameter remains constant also if the FUNCTION switch is still depressed. FUNCTION q 28 ADVANCED BASS EFFECTS PROCESSOR Reference value < RTM parameter maximum value Reference value > RTM parameter Reference value Reference value FUNCTION switch FUNCTION switch minimum value STEP 12 Release the FUNCTION switch. The RTM control target parameter gradually returns to the original value. · You can release the FUNCTION switch already before the maximum (minimum) value is reached. For some effect parameters, simply pressing and releasing the FUNCTION switch will yield an interesting effect. · When the remote pedal RP01 is connected, RTM can also be controlled with the foot pedal of the RP01. FUNCTION HINT Using the FUNCTION switch 29 q ADVANCED BASS EFFECTS PROCESSOR Controlling the Volume in Real Time (Volume RTM) When the FUNCTION mode is set to "9: RTM", the Volume RTM function is also available, allowing volume adjustment in real time. This makes it possible to easily perform fade- out or fade-in during a performance. POSITION FUNCTION MODE BANK(VALUE) COMP 1. COMP2. COMP2 3. LIMITER 4. DUAL COMP 5. DEFRET 6. SLAP Sens/Sens 1 Atk/Sens 2 Peak/X-F Tone/Bal Level VOLUME RTM DIST/AMP WAH EQ 1. GRAPHIC 2. 3-BAND 3. PARAMETRIC 8kHz/High/F1 4kHz/MidF/G1 2kHz/MidG/F2 1kHz/Low/G2 Level ZNR SYNTH EFFECT DLY/REV 1. CLN1 2. CLN2 1. AUTO 2. PEDAL 3. TE-C 4. SW-C 3. OCT 4. PHASE 5. OD 6. FUZZ 5. ENH 6. P-EQ 7. FN-D 8. AC-D 7. GRAPHIC EQ Gain/Mid Enh Level D. Level Cabinet 1:DIST-WAH 2:WAH-DIST DIST/AMP RTM Dpt/F1/500Hz Spd/G1/250Hz Color/F2/100Hz Mode/G2/500Hz Level WAH RTM 1-6. BASS SYNTH 1. CHO 2. FLG 1. DELAY 4. P-PIT 2. HALL 3. ROOM 7. HARMO SYNTH 3. PIT 5. DETUNE 6. TRILL 4. EARLY REF 7. SWEEP 8. RING 5. DLY+REV Freq/Mode Reso/Scale Decay/Atk D. Level Level SYNTH RTM Color/Pit/Dly Dpt/Sft/Mode Rate/Tone Mix/Bal/Reso FUNCTION Mode EFFECT RTM DlyTime/RevTime FineTime/DlyMix FB/RevColor DlyMix/RevMix Patch Level DLY/REV RTM 1. BANK DOWN 2. MANUAL 3. HOLD DLY(LONG) 4. HOLD DLY(REAL) 5. DELAY(TAP) METRO TEMPO 6. BYPASS 7. MUTE 9. RTM USER METRO VOL METRO ON/OFF U UO PRESET (BOTH) BANK FUNCTION 1, 4 6, 7 3 2 2 INPUT ATT MASTER HIGH MASTER MID EDIT(CANCEL) GROUP STORE MASTER LOW VALUE ADVANCED BASS EFFECTS PROCESSOR STEP 1 2 Press the EDIT key to activate the Edit mode. EDIT(CANCEL) STEP Using the FUNCTION switch Use the Module Select keys and the Parameter Select keys to choose parameter 6 (Volume RTM) of the COMP module. VOLUME RTM Parameter 6 of the COMP module serves for turning Volume RTM on and off. MASTER MID MASTER LOW STEP 3 Use the VALUE knob to set the display indication to "on". VALUE Volume RTM can now be used. on EDIT(CANCEL) STEP 4 5 Press the EDIT key to revert to Play mode. If necessary, store the patch as described on page 19. The Volume RTM setting can be stored for each patch. STEP Set the FUNCTION Mode to "9: VOLUME". For details, please refer to page 21. q 30 ADVANCED BASS EFFECTS PROCESSOR STEP 6 While playing your instrument, press and hold the FUNCTION switch. FUNCTION switch LED lit FUNCTION The effect volume will be gradually reduced to zero. NOTE The volume here refers to the input level of the EFFECT module, not the overall level of the 3000B. If for example delay or reverb is used, only the original sound is reduced, and the delay or reverb sound is still audible. STEP 7 Release the FUNCTION switch. FUNCTION The volume gradually returns to the original value. s Volume RTM on Reference value VOLUME FUNCTION switch LED OUT No sound FUNCTION switch Using the FUNCTION switch HINT · In step 6, you can release the FUNCTION switch before the volume zero point is reached. · When the remote pedal RP01 is connected, Volume RTM can also be controlled with the foot pedal of the RP01. ADVANCED BASS EFFECTS PROCESSOR 31 q Returning the 3000B to the Factory Default Settings This section describes use of the Special mode (All Initialize and Factory Recall). All Initialize is a special function for returning all the patches in the USER group and the values of the global parameters to their factory settings. Factory Recall allows selective return of a specified patch to the factory default. NOTE Keep in mind that any patches you have stored will be erased if you implement the All Initialize function. POSITION FUNCTION MODE BANK(VALUE) COMP 1. COMP2. COMP2 3. LIMITER 4. DUAL COMP 5. DEFRET 6. SLAP Sens/Sens 1 Atk/Sens 2 Peak/X-F Tone/Bal Level VOLUME RTM DIST/AMP WAH EQ 1. GRAPHIC 2. 3-BAND 3. PARAMETRIC 8kHz/High/F1 4kHz/MidF/G1 2kHz/MidG/F2 1kHz/Low/G2 Level ZNR SYNTH EFFECT DLY/REV 1. CLN1 2. CLN2 1. AUTO 2. PEDAL 3. TE-C 4. SW-C 3. OCT 4. PHASE 5. OD 6. FUZZ 5. ENH 6. P-EQ 7. FN-D 8. AC-D 7. GRAPHIC EQ Gain/Mid Enh Level D. Level Cabinet 1:DIST-WAH 2:WAH-DIST DIST/AMP RTM Dpt/F1/500Hz Spd/G1/250Hz Color/F2/100Hz Mode/G2/500Hz Level WAH RTM 1-6. BASS SYNTH 1. CHO 2. FLG 1. DELAY 4. P-PIT 2. HALL 3. ROOM 7. HARMO SYNTH 3. PIT 5. DETUNE 6. TRILL 4. EARLY REF 7. SWEEP 8. RING 5. DLY+REV Freq/Mode Reso/Scale Decay/Atk D. Level Level SYNTH RTM Color/Pit/Dly Dpt/Sft/Mode Rate/Tone Mix/Bal/Reso FUNCTION Mode EFFECT RTM DlyTime/RevTime FineTime/DlyMix FB/RevColor DlyMix/RevMix Patch Level DLY/REV RTM 1. BANK DOWN 2. MANUAL 3. HOLD DLY(LONG) 4. HOLD DLY(REAL) 5. DELAY(TAP) METRO TEMPO 6. BYPASS 7. MUTE 9. RTM USER METRO VOL METRO ON/OFF U UO PRESET (BOTH) BANK FUNCTION 2, 3 INPUT ATT MASTER HIGH MASTER MID EDIT(CANCEL) GROUP STORE MASTER LOW VALUE ADVANCED BASS EFFECTS PROCESSOR STEP 1 Cut the power supply to the 3000B. [. . . ] DLY+REV DlyTime 1­50 DlyMix ( RTM) 0­100 FB 0­10 RevMix 0­100 FineTime 0­50 RevColor(Tone) 0­10 RevMix ( RTM) 0­100 Patch Level(P) 1­50 DLY/REV RTM oF, 0­100 RevColor(Env) -10 ­ +10 s Parameter 1 TYPE (Effect Type) The DLY/REV module comprises the following five effect types. q Parameter 1 RevTime Determines the duration of the reverb. q Parameter 2 FineTime Determines the pre-delay interval until the reverb sound starts Type 1 Type 2 Type 3 Type 4 Type 5 DELAY HALL (Hall Reverb) ROOM (Room Reverb) EARLY REFLECTION DELAY+REVERB (Delay and Reverb connected in series) q Parameter 3 RevColor (Tone) Attenuates the high-frequency range of the effect. q Parameter 4 RevMix ( RTM) Determines the mix ratio of the effect sound. s Type 3 ROOM (Room Reverb) Depending on the selected effect type, the content of parameters 1 - 4 changes. The parameter content is the same as for Type 2 (HALL). s Type 1 DELAY Conventional delay effect with a maximum delay time of 1000 milliseconds. s Type 4 EARLY REFLECTION A reverb effect that stresses the early reflections. Effect Types and Parameters q Parameter 1 DlyTime Determines the delay time in 100-ms steps. q Parameter 2 FineTime Determines the delay time in 1-ms steps. q Parameter 1 RevTime q Parameter 2 FineTime q Parameter 3 RevColor (Env) Determines the reverb envelope. Negative values result in reverse reverb. q Parameter 3 FB Determines the delay feedback amount. q Parameter 4 DlyMix ( RTM) Determines the mixing balance between effect sound and original sound. [. . . ]