Detailed instructions for use are in the User's Guide.
[. . . ] Installation and Operating Guide | Warranty Model Number | H20F50DT | HealthView TM TV
table of contents
page
5
© Copyright 2003, Zenith Electronics Corporation
RECORD THE MODEL NUMBER
For Customer Support/Service please call:
1-888-865-3026
www. zenith. com
The serial number of this HealthViewTM TV is located on the back of the cabinet. For future reference, we suggest that you record the serial number here: MODEL NO. H20F50DT SERIAL NO. ____________________________________
WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] PAGE 26
206-3491-O
Managing the Channel Banks
Using the optional Installer's remote control, the TV has four channel banks, where the administrator or installer can store groups of TV channels
PLANNING THE CHANNEL BANKS Generally, TV channels are grouped into "program packages" with terms that are proposed to the end user. You may plan your package by using a chart like the one after the following page. Remember, you can "blank" a channel for accommodating audio-only, such as an FM radio station or in-house communication. You may leave any unused bank with the channels entered during Auto Program; or, you may delete the channels. However, you may want to leave at least one channel in any unused bank. Then, if someone selects an "unused" bank, that channel will assure them that the TV is functional. Note: Some channels from factory testing may be in the channel banks if you have not yet run Auto Program. ADDING / DELETING CHANNELS A previously prepared programming chart is helpful. All channels found on your cable/antenna will be entered in Channel Banks 1, 2, 3, and 4. Note: Be advised that running Auto Program overwrites any custom channel setups; removes Blanked, Deleted. Select a channel bank with an installer remote - -press SOURCE/BANK (and repeat). CHANNEL BANK and BANK number will be displayed.
CHANNEL BANK BANK 1
Channel bank number display
Channel Bank
Program package
1 Basic cable channels 2 Extended cable channels 3 Extended with premium channels 4 Other cable installer options (Grouping is provided as an example only. )
3. Use the ADD/DEL/BLNK item (also in the Setup menu) to customize your program package. You can also "Blank" a channel for accommodating an audio-only program source or in-house communication. Inactive TV Display (Channel Bank 4) The TV can be set up to be inactive; which would require an attendant using an installer remote to change to a "billable" active channel bank selection: Bank 1, 2, or 3. Note: For institution control of patient-accessible programming, channels in Bank 4 need to be removed.
The BLNK (blank) channel function is "global" -- the same channel number is blanked in channel banks 1, 2, 3, and 4.
INACTIVE TV PLEASE . CALL ATTENDANT
206-3491-O
PAGE 27
Managing the Channel Banks
Examples of typical channel banks charts
Figure 1. Typical channel banks after running Auto Program
B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1
2
3
4
5
6
7
8
9
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A A A A
A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk
B Purpose A N K 1 2 3 4 Basic Extend All CTV Other Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1
2
3
4
5
6
7
8
9
BC A BC A BC A BC A
A A A A
A A A A
A A A A
A A A A
D A A A
D D D A
D A A A
D A A A
D D D A
D A A A
D A A A
D A A A
D D A A
D D D A
D D A A
D D A A
A = Active D = Deleted BC = Blanked Channel
Channel was found during AUTO PROGRAM Channel was deleted using Add/ Del option. Channel was blanked using BLANK channel option (ADD/DEL/BLNK).
ADDING / DELETING CHANNELS It is best to do ADD / DEL customizing before doing "BLNK. " AUTO PROGRAM enters the same channels in Banks 1, 2, 3, and 4. AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted.
ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4. [. . . ] Multiple Protocol Interface: Zenith protocol for external control of TV through RJ11 (M. P. I. ) input jack on TV connections panel. jack is used for cloning TV's features. ) Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. Picture and sound traveling through a cable, or over the air, to the television screen. Device that picks up the audio/video signal and turns it into picture and sound. [. . . ]