User manual ZEKTOR HDS4X2

[. . . ] Home Theater Solutions HDS4x2 Component Video / Audio Matrix Switch Table of Contents What's Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Overview of the HDS4x2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 2 3 3 4 4 4 5 5 Getting Started (Quick Reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mapping an input to an output zone using the remote control's direct select buttons . [. . . ] Once the front panel is flashing, press the `2' button 2 , or 2 on the remote. The HDS4x2 is now in the "Control settings" mode. This mode allows different settings of the HDS4x2 to be enabled or disabled. Each setting is numbered, and selected by using the Zone buttons to scroll through the setting numbers 4 . Once a setting is selected, it can be enabled / disabled by pressing the Breakaway button 3 . A setting is enable by turning on the BLUE LED, it's disabled by turning on the RED LED. When this setting is disabled, each button can be individually enabled or disabled. For more information in this setting see the section entitled: "Disabling front panel buttons", on page 12. For more information in this setting see the section entitled: "Disabling the remote IR buttons", on page 13. When disabled, no IR can be received through the front panel IR sensor, the IR jack is not affected. When disabled, no IR codes can be received through the rear panel IR Jack, the front panel IR sensor is not affected. When disabled, only pressing the Power Toggle button (or the and ON buttons on the remote), 1 2 - 8 2 or A - H , if these butwill turn on the HDS4x2. This option does not affect the IR buttons tons are enabled, they will always turn on the HDS4x2. When enabled, and 12V is applied to the IR Jack, the HDS4x2 will power on, when the 12V is removed, the HDS4x2 will power off. For more information in this setting see the section entitled: "12V on / off control", on page 25. 07 If set, then video will be muted as well as audio when a mute discrete code is received by the HDS4x2. If reset, then only the audio will be muted when a discrete code, to mute a zone, is received by the HDS4x2. HDS4x2 User Guide, Rev 1. 1, 08-31-07 11 Advanced Control Features Disabling front panel buttons 1 2 3 4 B/A HDS4x2 Enter / Exit 1 setup mode 2 Select "Control settings" Toggle setting on/off 3 4 Select setting To enable or disable the front panel buttons: 1. "Enter the setup mode", by pressing and holding the power toggle button 1 until the display flashes, or by pressing SET and then on the remote. Press the Power Toggle button 1 , exit the setup mode and return to normal operations, or continue onto the next section entitled: "Disabling individual front panel buttons". NOTE: Even with the front panel buttons disabled, you will still be able to enter the setup mode by holding the Power Toggle button. This allows you to re-enable the front panel buttons even though the buttons themselves are disabled. 2 on the remote. Disabling individual front panel buttons 1 2 3 4 B/A HDS4x2 Select "Button enable / disable" Mode 5 Enable / Disable 6 selected button 7 Select button number To enable / disable individual front panel buttons, start by disabling all the front panel buttons, by performing `1' through `4' of the above steps. After the front panel is disabled, you can now re-enable individual buttons by selecting the "Button enable / disable" mode, by pressing the `3' button 5 . The decimal point on Zone 2 will light up to indicate the new mode selection. [. . . ] 480i - 1440p60, all HDTV modes, includes 1080p24 & 1080p60 Input impedance . YPbPr, RGB with sync on green, Composite, S-Video (w/adapter cable) Analog Audio Bandwidth . 4 Coax, 4 Optical (w/ auto conversion between formats) S/PDIF outputs . 2 Coax, 2 Optical (coax mirrors optical for each zone) Transfer rates . [. . . ]