User manual ZEKTOR HDS4.1

[. . . ] All digital audio inputs are automatically conver ted to both Coax and Optical outputs. All three outputs are available at all times, and are all individually buffered to allow dr iving three different digital audio de vices simultaneously. 2 HDS4. 1 Component Video Switch HDS4. 1 Component Video Switch Step 1: Make the appropriate connections. To Composite Monitor w/Analog Audio Easy, Simple, Instructions! DIGITAL AUDIO R/V L/H C/V R/V L/H C/V R/V L/H C/V R/V L/H C/V R/V L/H C/V 1 2 3 Step 1. . . 1 Y/G Pb/B Pr/R 2 Y/G Pb/B Pr/R 3 Y/G Pb/B Pr/R 4 Y/G Pb/B Pr/R OUT 1 2 3 4 OUT 9VDC · Y/G Pb/B Pr/R 4 OUT OUT Unused Input To Cable Box To DVD To Game Console To Cable Box Digital Audio To Game Console Digital Audio To Projector or Monitor To DVD Digital Audio To Home Theater Receiver's Digital Audio Input To Power Module · Step 2. . . Use the analog input connec tions to switch component video / composite video / analog audio or any combination of the above signals to the HDS4. 's analog output connec tors. Use the digital audio connec tors to switch digital audio signals, with full for mat conversion bet ween the optical and coax digital audio for mats. Plug the power module into the HDS4. , and plug the module into a standard A. C. [. . . ] are tur ned off. Step 2: Select "Lighting Mode" option ZEKTOR The intensities of the both the br ight and dim levels can be adjusted as well, this is explained in the nex t chapter. To change the front panel lighting mode. . . 4 1 2 3 Step 1: Enter the Setup Mode · · · The HDS4. is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the `' button to selec t the "Lighting M ode" option. The front panel selec tion LEDs now indicate the cur rently selec ted light mode as follows: I f `' is lit, then front panel lights are always off. I f `4' is lit, then front panel lights auto -fade from br ight to dim af ter 4 seconds of inac tivit y. Choose a new light control mode by pressing the associated selec tion button. Press the Power Button to save the new mode and retur n to nor mal operations. After `' is pressed, the standby LED continues to flash, and the front panel will display the current Light Mode setting. Step 2: Select the Lighting Mode option Step 3: Choose a new lighting mode ZEKTOR 1 2 3 4 Step 3: Choose a new lighting mode Auto-Fade Always Bright Always Dim Always Off Exit Setup Mode · · Note: The lighting mode setting is saved in non-volatile memor y and is not affec ted by a power failure. HDS4. 1 Component Video Switch HDS4. 1 Component Video Switch Step 1: Place the HDS4. 1 into the Setup Mode ZEKTOR Adjusting the Front Panel Intensity The br ight and dim levels of the front panel lights of the HDS4. To change the front panel intensities. . . 1 2 3 4 Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. Step 1: Enter the Setup Mode · · · The HDS4. is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the `4' button to selec t "Front Panel I ntensit y " option. The front panel selec tion LEDs now indicate the front panel intensit y settings: I f `' is lit, then the DIM level is being adjusted. Use the `' and `2' buttons to switch bet ween the DIM and BRIGHT settings. Use the `' button to decrease the intensit y of the front panel lights. Use the `4' button to increase the intensit y of the front panel lights. You cannot make the DIM level br ighter than the BRIGHT level, and you cannot make the BRIGHT level dimmer than the DIM level. Once the front panel intensities are acceptable, press the Power button to save the new settings and exit the setup mode. Step 2: Select "Front Panel Intensity" option ZEKTOR Step 2: Select the Front Panel Intensity option 1 2 3 4 After `4' is pressed, the standby LED continues to flash, and the front panel will display the current intensity setting. Step 3: Adjust Front Panel Intensities Step 3: Adjust front panel intensities ZEKTOR · · · · · 1 2 3 4 Press to Brighten LEDs Press to Dim LEDs Selects BRIGHT level Selects DIM level Exit Setup Mode Note: The new intensit y settings are saved in non-volatile memor y and are not affec ted by a power failure. 0 HDS4. 1 Component Video Switch HDS4. 1 Component Video Switch Step 1: Set the HDS4. 1 to the preferred initial power on state Setting the Initial Power On State As long as the HDS4. is plugged in, it will remember the previously selec ted input in standby mode. When powered up by pressing the Power button, it will retur n to that previously selec ted channel. However, if power is removed (for instance a plug str ip used to power the HDS4. is tur ned off ), and then re -applied, the HDS4. 's default behavior is to enter into the standby mode. To change the power on defaults. . . ZEKTOR 1 2 3 4 Setup the HDS4. [. . . ] This war rant y gives you specific legal r ights, and you may also have other r ights that var y from state to state and countr y to countr y. Contact Information Instructions for Returning Items Please retain the dated sales receipt as evidence of the date of purchase. I f you bought the produc t through a dealer, installer, or reseller, you will need to retur n the produc t to the point of sale. E-mail us, or call us, using the infor mation listed under "Customer S er vice Contac t I nfor mation", for a R etur n to M anufac turer Author ization (RMA) number. The RMA # must appear on your retur n pack ing label or on the outside of the box. [. . . ]