User manual ZEKTOR CVS4

[. . . ] All three outputs are available at all times, and are all individually buffered to allow dr iving three different digital audio de vices simultaneously. CVS4 Component Video Switch Step 1: Make the appropriate connections. To Composite Monitor w/Analog Audio Easy, Simple, Instructions! RS-232 IR / Z-IN Z-OUT R/V L/H C/V R/V L/H C/V R/V L/H C/V R/V L/H C/V R/V L/H C/V 1 2 3 1 Y/G Pb/B Pr/R 2 Y/G Pb/B Pr/R 3 Y/G Pb/B Pr/R 4 Y/G Pb/B Pr/R OUT DIGITAL AUDIO Step 1. . . · Y/G Pb/B Pr/R 4 OUT OUT 1 2 3 4 OUT 9VDC Unused Input To Cable Box To DVD To Game Console To Cable Box Digital Audio To Game Console Digital Audio To Projector or Monitor To DVD Digital Audio To Home Theater Receiver's Digital Audio Input To Power Module Step 2: Press buttons to select an input. 1 2 3 4 · · · Step 2. . . Use the analog input connec tions to switch component video / composite video / analog audio or any combination of the above signals to the C VS4's analog output connec tors. Use the digital audio connec tors to switch digital audio signals, with full for mat conversion bet ween the optical and coax digital audio for mats. I f using a hardwired IR controller to operate the C VS4, connec t the controller IR cable to the IR / Z-IN jack . I f using a PC (or other ser ial controller), connec t it to the RS -22 por t using a standard ser ial cable. [. . . ] The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. Note: · · · · Front panel lights af ter 4 seconds of Front panel lights Front panel lights Front panel lights automatically fade from br ight to dim inac tivit y. are tur ned off. Step 2: Select "Lighting Mode" option 1 2 3 4 The intensities of the both the br ight and dim levels can be adjusted as well, this is explained in the nex t chapter. To change the front panel lighting mode. . . Step 1: Enter the Setup Mode · · · The C VS4 is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the `' button to selec t the "Lighting M ode" option. The front panel selec tion LEDs now indicate the cur rently selec ted light mode as follows: I f `' is lit, then front panel lights are always off. I f `4' is lit, then front panel lights auto -fade from br ight to dim af ter 4 seconds of inac tivit y. Choose a new light control mode by pressing the associated selec tion button. When powered up by pressing the Power button, it will retur n to that previously selec ted channel. However, if power is removed (for instance a plug str ip used to power the C VS4 is tur ned off ), and then re -applied, the C VS4's default behavior is to enter into the standby mode. To change the power on defaults. . . 1 2 3 4 Setup the CVS4 to the initial power on state you'd prefer. Step 1: Setup the CVS4 to your preferred power on state. · Use the front panel buttons to setup the C VS4 to the operating settings you'd like at initial power up. While continuing to hold the Power button, press and hold the `' button. Af ter holding both buttons for about `4' seconds, the display will blink indicating the new power on defaults have been accepted. You can test the new defaults by either disconnec ting the power supply from the back of the C VS4 or by unplugging the power supply from the wall. The C VS4 will power up into your new power on default state. Step 2: Save the new initial power on state. Step 2: Save the new initial power on state 1. 3. 1 2 3 4 Test the new initial power on state · · 1 Start by pressing and holding the Power button. . . 2 3 . . . while continuing to hold the Power button, press and hold the `' button. After about 4 seconds, the display will flash indicating the new power on state has been accepted. 4 CVS4 Component Video Switch CVS4 Component Video Switch Step 1: Enter the Enable / Disable Control State Disabling Front Panel or Remote I f you are not planning on using a remote control with your C VS4, you might want to disable its remote control func tion. Or if you have a household with young cur ious fingers that likes playing with buttons, you also have the capabilit y of disabling the front panel switches and only operating the C VS4 with a remote. To enable/disable the front panel switches or remote capabilities. . . 1 2 3 4 Step 1: Enter the Enable / Disable control state 1 Start by pressing and holding the Power button. . . 2 3 . . . while continuing to hold the Power button, press and hold the `4' button. 1. 3. After about 4 seconds, the standby LED will flash quickly, and the display will indicate the current enable / disable statuses. · First press and hold the Power button While continuing to hold the Power Button, press and hold the `4' button. Af ter holding both buttons for about `4' seconds, the standby LED will star t flashing quick ly indicating you are now able to enable / disable front panel buttons and IR control func tions. The front panel selec tion LEDs now indicate the state of the front panel and IR control settings: I f `' is lit, then the Front Panel buttons are ENABLED. Use the `4' button to ENABLE / DISABLE the IR remote control func tions. When finished, press the `Power ' button to save new settings and retur n to nor mal operations. Step 2: Enable or Disable Front Panel and / or IR Control Functions Step 2: Enable or Disable Front Panel and / or IR control 1 2 3 4 · · · Enable / Disable IR Control Functions Enable / Disable Front Panel Buttons Exit Setup Mode Note: D isabling the front panel buttons does not disable the abilit y to enter the S etup Modes. Even with the front panel disabled you c an per form the above steps, allowing you to once again enable the front panel buttons. 6 CVS4 Component Video Switch CVS4 Component Video Switch 7 Step 1: Reset All Parameters to Factory Defaults Resetting to Factory Defaults I f, for whatever reason, you'd like to reset your C VS4 back to its fac tor y condition, this is easily done. . . 1 2 3 4 Step 1: Reset All Parameters to Factory Defaults 1. [. . . ] This war rant y gives you specific legal r ights, and you may also have other r ights that var y from state to state and countr y to countr y. Contact Information Instructions for Returning Items Please retain the dated sales receipt as evidence of the date of purchase. I f you bought the produc t through a dealer, installer, or reseller, you will need to retur n the produc t to the point of sale. E-mail us, or call us, using the infor mation listed under "Customer S er vice Contac t I nfor mation", for a R etur n to M anufac turer Author ization (RMA) number. The RMA # must appear on your retur n pack ing label or on the outside of the box. [. . . ]