User manual ZANUSSI ZXT5050IE

[. . . ] Ensure that all control knobs are in the OFF position when not in use. Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance. If the appliance is out of order, disconnect it from the electric supply. Child Safety This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. [. . . ] 1 FO 0204 A - Burner cap B - Burner crown C - Ignition candle D - Thermocouple Always turn the flame down or put it out before taking the pans off the burner. 12 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel. It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated. Burner Big (rapid) Medium (semirapid) Small (Auxiliary) minimum diameter 160 mm. 160 mm. Use of electric plates To switch on the plates, turn the relevant knob to the required position. The plates are regulated by a 7 position switch: Position 0: off Position 1: minimum disbursement of heat Position 6: maximum disbursement of heat The pilot light signals the connection of the electric plate. It is important to note that the plate may smoke a little and produce a slightly unpleasant odour when used for the first time. This is quite normal and will disappear after a few minutes. Using the plates correctly l l l l When cooking by electric, saucepans should have a thick base and be perfectly flat in order to ensure total contact with the plate and, consequently, perfect conduction (Fig. Occasionally, saucepans have a thin bottom and these loose their shape over a period of time. In this manner two of the qualities of the electric plate are lost: the even distribution of heat and the saving of energy. As regards the size of the saucepans: for best results, the plate and the saucepan should have the same diameter. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut GJ 1/2". Screw the parts without forcing, adjust the connection in the required direction and tighten everything. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. A) Ramp with ending nut B) Seal C) Adjustable connection FO 0264 Fig. 4 15 Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. This has to be provided with a proper plug, able to support the load marked on the identification plate. [. . . ] minimum from the hob. 55 m in. 550 Fig. 9 FO 2098 Fitting the hob to the worktop The hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in fig. To install the hob, proceed as follows: 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition candles are not damaged in this operation. 2) Place the sealing gasket (supplied with the hob) on the edges of the cut out: place it exactly on the front and rear edge, taking care that the sealings meet without overlapping; 3) Fix the hob with the relevant screws (fig. The traction of the screws is able to trace the sealing, any excess of which can be easily removed. [. . . ]