User manual ZANUSSI ZWN6105

[. . . ] User Manual Washing machine ZWN 6105 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - -6-7 Programme table - - - - - - - - - - - - - - - - -9-10 Programme information - - - - - - - - - - - - - -11 Washing Hints - - - - - - - - - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -14 Operating Sequence - - - - - - - - - - - - - - - -15 Care and cleaning - - - - - - - - - - - - - - - - - -18 Something not working - - - - - - - - - - - - - - 20 Technical data- - - - - - - - - - - - - - - - - - - - - 23 Consumption values - - - - - - - - - - - - - - - - 24 Installation - - - - - - - - - - - - - - - - - - - - - - - 25 Environmental concerns - - - - - - - - - - - - - 27 2 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. [. . . ] (refer to the section «Programme table» for the maximum allowed spin speed). Select the desired option by means of buttons 3, 4, 5 and 6 Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before depressing the button 8. For the compatibility of the options with the washing programmes, refer to the section «Programmes table». Start the programme by pressing button 8 To start the selected programme, press this button; the corresponding green pilot light stops flashing. On programme progress display the pilot light 9 illuminates to indicate that the appliance starts operating and the door is locked. If an option which is not compatible with the set wash programme is selected, the message Err is displayed for few seconds and the red light of this button flashes for 3 times. Measure out the amount of detergent required, pour it into the main wash compartment and, if you wish to carry out a programme with the prewash phase or the soak programme, pour it into the compartment marked . If required, pour fabric softener into the compartment marked (the amount used must not exceed the «MAX» mark in the drawer). Select the required programme by means of the programme selector dial (1) Turn the programme selector dial to the required programme. The green light of button 8 starts to flash. It can be turned either clockwise or anticlockwise. On position «O» the programme is reset and the machine is switched OFF. At the end of the programme the selector dial must be turned to position «O», to switch the machine off. Select the delayed start by pressing button 10 Depress button this button to select the required delay. The selected delay time value will appear on the display for few seconds, then the duration of the programme will appear again. You must select this option after you have set the programme and before you press the button 8. You can cancel the delay time at any moment, before you press button 8. If you have already pressed it, and you wish to cancel the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 10 once. · If the programme has already started, the selected delay can be modified only after you have turned the programme selector dial to the «o» position and after you have selected the programme again. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 8 before opening the door. The Delay Start cannot be selected with «Drain» programme. Display The display shows the following information: After selecting a programme the duration of the selected programme appears on the display. During the programme, the time remaining is updated every minute. 2. 00 The Delayed start appears on the display for about 3 seconds, then the duration of the previously selected programme is displayed. The delay time value decreases by one unit every hour and then, when 1 hour remain, every minute. The incorrect option selection is indicated by the message Err displayed for few seconds and by flashing of the light button 8. [. . . ] Unscrew and remove the two large rear bolts B and the six smaller bolts C. E C C D 5. Remove the bracket D, refit the six smaller bolts C and slide out the relevant plastic spacer E. Water inlet The inlet hose is already screwed on the back of the appliance. Do not use the hose from your previous machine to connect to the water supply. 25 HEC0006 Attenzione!Angle the hose to the left or right depending on the position of your water tap. [. . . ]