User manual ZANUSSI ZWI2125

[. . . ] User Manual Washing Machine Centrifugeren Centrifugeren Pompen Spoelen Inweken Inweken 30° Gordijnen Gordijnen 40° Sport Spor t 40° intensief Wol 40° Handwas Handwas 30° Handwas Handwas 40° 95° 60° eco 60° 40° 30° 60° 40° 30° 30° Anti-kreuk 40° 40° Anti-kreuk ZWI 2125 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - - - -6 Programme table - - - - - - - - - - - - - - - - - -10 Programme information - - - - - - - - - - - - - -12 Washing Hints - - - - - - - - - - - - - - - - - - - - -13 Before the first use - - - - - - - - - - - - - - - - -16 Operating Sequence - - - - - - - - - - - - - - - -17 Care and cleaning - - - - - - - - - - - - - - - - - -20 What to do if. . . [. . . ] You can cancel the delay time at any moment, before you press button 8. If you have already pressed it, and you wish to CANCEL the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 10 once. · The selected delay can be modified only after you have turned the programme selector dial to the «O» position and after you have selected the programme again. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 8. The door can be opened immediately or after a few minutes depending on the model. The Delay Start cannot be selected with «Drain» programme. Altering an option or a running programme It is possible to change some option before the programme carries it out. Before you make any change, you must pause the washing machine by pressing button 8. Turn the programme selector dial to «O» and then to the new programme position. Interrupting a programme Depress button 8 to interrupt a programme which is running, the corresponding light starts to flash. Cancelling a programme Turn the selector dial to «O» to cancel a programme which is running. Opening the door after the programme has started First set the machine to pause by pressing the button 8. If the light 9 goes off, the door can be opened immediately or after a few minutes depending on the model. If it does not switch off, this means that the machine is already heating, that the water level is too high. If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to «O». After a few minutes the door can be opened (Pay attention to the water level and temperature!). After this procedure, it will be necessary to set the programme and the options again and then to depress button 8. Some acustic signals sound and on the display will appear a flashing «0 ». If at the end of a programme there is water in the tub, the light 9 remains on and the door is locked to indicate taht the door must be empty out. at the end of programme, the display shows a flashing zero «0», the light 9 goes off and it will be possible to open the door. At the end of the cycle, turn the programme selector dial to «O» to switch the machine off. Remove the laundry from the drum and carefully check that the drum is empty. Leave the door open to prevent the formation of mildew and unpleasant smells. 19 Care and cleaning IMPORTANT!You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. [. . . ] To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet (4) on the appliance (see picture D). 31 416 818 120 1 1 2 7 3 5 B 23 8 a) Door The dimensions of the door should be: - width 595-598 mm - thickness 16-22 mm 820 min 176, 5 416 C 22+1 , 5 B suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point. The height (C-Fig. [. . . ]