User manual ZANUSSI ZTE130

[. . . ] If the machine is used for any other purposes or is not used correctly, the manufacturer accepts no responsibility for any damage that might occur. · Clothes which are dripping wet should not be placed in the dryer. · Danger of explosion: Never tumble dry items that have been in contact with inflammable solvents (petrol, methylated spirits, dry cleaning fluid and the like). Risk of fire: items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed on the tumble dryer, · If you have washed your laundry with stain remover you must execute an extra rinse cycle before loading your tumble dryer. [. . . ] Check that your domestic electrical installation can take the maximum load required (2. 2 kW), also taking into account any other appliances in use. Connect the machine to an earthed socket, in accordance with current wiring regulations. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre. P1106 Should the appliance be moved, it must be transported vertically. Important!The power supply cable must be accessible after installing the machine. Positioning It is recommended that, for your convenience, the machine is positioned close to your washing machine. The tumble dryer must be installed in a clean place, where dirt does not build up. Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine. To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface. Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. Do not restrict the floor clearance through deeppile carpets, strips of wood or similar. This might cause heat build-up which would interfere with the operation of the appliance. Please check the laundry does not get caught between the door and filter. If required, press the low temperature button and/or the buzzer OFF button . Press the Start button for 2 seconds: light comes on and drying starts. All drying programmes end with a 10 minute cooling phase (light is on). If the laundry is not removed at the end of the cycle, the dryer performs an anti-creasing phase (duration: 30 minutes maximum). The buzzer sounds every 10 seconds (if the button has not been pressed). Lights and flash alternately. If you do not remove the laundry, the dryer will stop automatically at the end of the anti-creasing phase. 9 ENGLISH Useful hints · Try to load to the maximum capacity of the machine as small loads are uneconomical. For information, here is a list of the average weights of some common laundry items. Sheet Tablecloth Kitchen towel Table napkin Towelling hand towel Bathrobe Man's shirt Pillowcase Man's pyjamas Ladies' nightdress 700 - 1000 g 400 - 500 g 70 - 120 g 50 - 100 g 150 - 250 g 1000 - 1500 g 200 - 300 g 100 - 200 g 400 - 500 g 200 - 250 g · Avoid drying dark clothes with light coloured fluffy items such as towels as they could attract the fluff. shirts, should be briefly pre-spun before drying (depending on crease resistance approx. [. . . ] The reservoir must be emptied after each drying cycle to ensure efficient operation when the machine is next used. If this is not done a safety device trips: pilot light on the control panel comes on and the programme stops, leaving the laundry damp. Proceed as follows: When your laundry does not reach the desired degree of dryness, in other words, when it turns out either too dry or too damp, we advise you to clean the inside of the drum with a cloth soaked with vinegar. This will eliminate the slight patina that has formed in the drum (due to residues of detergent and softeners used in the washing, and to the lime contained in the water), which prevents the probes from detecting the correct degree of dryness. · Pull out the reservoir · Turn it upside down and let water flow down · Re-fit the reservoir P1156 P1204 The reservoir must be re-inserted correctly. [. . . ]