User manual ZANUSSI ZKH2145

[. . . ] User manual Washerdryer ZKH 2145 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - -6-8 Programme table - - - - - - - - - - - - - - - - -9-10 Programme information - - - - - - - - - - - - - -11 Washing and drying hints - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -15 Operating Sequence - - - - - - - - - - - - - - - -15 Washing - - - - - - - - - - - - - - - - - - - - - - - - -15 2 Drying - - - - - - - - - - - - - - - - - - - - - - - - - -19 Drying programmes - - - - - - - - - - - - - - - - -20 Care and cleaning - - - - - - - - - - - - - - - - - -21 Something not working - - - - - - - - - - - - - - 24 Technical data- - - - - - - - - - - - - - - - - - - - - 28 Consumption values - - - - - - - - - - - - - - - - 29 Installation instruction - - - - - - - - - - - - - - - 30 Environmental concerns - - - - - - - - - - - - - 33 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. [. . . ] Select the spin speed or the Rinse Hold option by pressing button 2 The relevant light will light up. When selecting a programme, the light corresponding to the maximum speed allowed for that programme will illuminate. Select the degree of dryness or the duration of the drying cycle by means of buttons 3 and 4 The relevant light illuminates. By depressing the button 3 it is possible to select the degrees of dryness for cotton or synthetics items. The washer dryer will 16 automatically adjust the duration of the drying cycle to the selected degree. Also this button allows you to select a drying time for Cottons and Synthetics from 10 minutes to 130 minutes (2. 10). Select the desired option by means of buttons 5 and 6 Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before depressing the button 8. For more information about the compatibility of the options with the washing programmes, refer to the section «Programme table». Select the delayed start by pressing the button 10 Depress this button to select the required delay. The selected delay time value will appear on the display for few seconds, then the duration of the programme will appear again. You must select this option after you have set the programme and before you press the button 8. You can cancel the delay time at any moment, before you press button 8. If you have already pressed it, and you wish to cancel the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 10 once. · If the programme has already started, the selected delay can be modified only after you have turned the programme selector dial to the «O» position and after you have selected the programme again. If you need to open the door, you must first set the washer dryer to PAUSE by pressing button 8. The Delay Start cannot be selected with «Drain» programme. Display The display shows the following information: After selecting a programme the duration of the selected programme appears in minutes or hours and minutes on the display . (e. g. The delay time value decreases by one unit every hour, 90 minutes and then, when 1 hour remain, every minute. The incorrect option selection is indicated by the message Err displayed for a few seconds and by flashing of the red light button 8. 2. 05) 2. 00 During the programme, the time remaining is updated every minute. In the event of operating problems, some alarm codes can be displayed, (see paragraph "Something not working"). Selected drying time After selecting a drying programme programme the drying time is shown in minutes or hours and minutes. After the programme has started, the time remaining is updated every minute. E20 The End of programme or the stop wit water left in the tub is indicated by a flashing zero «0». 1. 00 0 Start the programme by pressing button 8 To start the selected programme, press this button; the corresponding green pilot light stops flashing. The pilot light 9 illuminates to indicate that the appliance starts operating and the door is locked. 17 The Delayed start appears on the display for about 3 seconds, then the duration of the previously selected programme is displayed. IMPORTANT! [. . . ] Do not use the hose from your previous machine to connect to the water supply. Angle the hose to the left or right depending on the position of your water tap. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use. 45° Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide supplied with the machine. [. . . ]