User manual ZANUSSI ZGF646CTN

[. . . ] In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power. Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation. The manufacturer disclaims any responsability should all the safety measures not be carried out. · · · · · · · Service · Under no circumstances should you attempt to repair the appliance yourself. [. . . ] It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated. · there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. ZGF 648 Push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. ZGF 643 After lighting the flame, keep the knob pushed down for about 5 seconds. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. If you cannot light the flame even after several attempts, check the "cap" (Fig. · Always turn the flame down or put it out before taking the pans off the burner. · Fig. 160 mm. Big (rapid) Medium (semirapid) Small (Auxiliary) 4 The Hob Lid In order to make the appliance match with the kitchen design, a lid (not provided) can be fitted on the hob. · The lid is meant to avoid dust to settle on the hob, when it is closed, and to collect splashes of oil or fat, when it is open. · Always clean the lid from cooking residues before opening it or taking it off. Always ensure all the burners are off before closing it. · Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Before fitting the appliance ensure that the installation has the correct voltage for the appliance. Such a drop in pressure is caused by the following parameters: maximum capacity of meter; diameter and lenght of the tube in front and behind the meter; section of transit of variuos tubes positioned on the circuit; diameter of eventual connections. · · · A) Ramp with ending nut B) Seal C) Adjustable connection IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Screw the parts without forcing, adjust the connection in the required direction and tighten everything. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. 4 6 Electrical connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. This has to be provided with a proper plug, able to support the load marked on the identification plate. To connect the plug to the cable, follow the recommendation given in Fig. If connecting the appliance directly to the electric system, it is necessary that you install a double pole switch between the appliance and the electricity supply, with a minimum gap of 3 mm. [. . . ] The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Carry out the building in of the hob as follows: · put the relevant sealings, supplied with the hob, on the edges of the cut out, as shown in Fig. 14, taking care that the sealings meet without overlapping; place the hob in the cut out, taking care of its centring; fix the hob with the relevant screws (Fig. [. . . ]