User manual ZANUSSI ZANS710

[. . . ] Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube. In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power. Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation. [. . . ] It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. 1 FO 0204 The Hob Lid Special lids are available on request which can give an aesthetic alignment with the kitchen units. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated. · It is recommended that the lid should never be closed when the burners are still hot. 28 2. Cleaning and Maintenance · Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. PERIODIC MAINTENANCE Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. q The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. FO 2110 Fig. Technical Data Gas Burners Rating Rapid Burner (big) 3 kW (G20-G25)) - 2, 8 kW (G30-31) Semirapid Burner (medium) 2 kW Auxiliary Burner (small) Category 1 kW II 2E+3+ Length Width 560 mm. 470 mm. Electric Supply HOB RECESS DIMENSIONS 230 V 50 Hz Setting Natural Gas 20 mbar / G25 25 mbar Gas connection G 1/2" 29 4. ADJUSTMENT OF MINIMUM LEVEL To adjust the minimum level of the burners, proceed as follows: · Light the burner. · With a thin screwdriver, adjust the by-pass screw (see Fig. 7 - "a"). If changing from natural gas to LPG, completely tighten clockwise the screw, until a small regular flame is obtained. Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position. 7 FO 1045 · This procedure can easily be carried out, anyhow the hob has been positioned or built in the working top. Auxiliary Semi-rapid Rapid Table 2 : injectors - (*) suitable for G25 too. BURNER NORMAL POWER kW REDUCED POWER kW NATURAL GAS G20 - 20 mbar inj. 1/100 Auxiliary (small) Semi-rapid (medium) Rapid (big) 1 2 Natural gas : 3 LPG : 2, 8 0, 33 0, 45 0, 65 70* 96* 119* m3/h 0, 095 0, 190 0, 286 NORMAL POWER LPG 28-30/37 mbar inj. Building In A = Auxiliary burner R = Rapid Burner SR = Semirapid burner These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 8. SR SR A R 580 Fig. 8 These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. Carry out the building in of the hob as follows: 55 m in. INSTALLATION AND ASSEMBLY Rear Wall · put the relevant sealings, supplied with the hob, on the edges of the cut out, taking care that the sealings meet without overlapping; 480 560 100 min FO 0275 · place the hob in the cut out, taking care of its centring; · fix the hob with the relevant screws (Fig. [. . . ] 12 30 60 a b 20 min 380 140 FO 1013 FO 0947 a) Removable panel b) Space possibly useful for connections Fig. 14 50 cm 2 120 cm 2 360 cm 2 FO 0938 FO 0939 180 cm 2 Fig. 16 550 min. FO 0198 560 min. FO 2099 650 mm 591 30 470 480 33 GUARANTEE - SPARE PARTS When calling for repairs during the period of guarantee ofthe appliance, the original invoice or receipt must be shown or sent together with the appliance to be repaired. General conditions of guarantee 1 The manufacturer guarantees the appliance indicated on the relative invoice for a period of one year from the date of purchase. [. . . ]