User manual ZANUSSI FLS674C

[. . . ] If the appliance is to stand on a carpeted floor make sure that there is space between the carpet and the supporting feet of the appliance for the air to circulate freely around. Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. It is dangerous to alter the the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance dos not stand on the electrical supply cable. [. . . ] The manufacturer declines any liability in case of accidents or incicents should these safety measures not be observed. Before plugging the appliance make sure that: 1º the mains of your installation is the same as on the rating plate of your appliance (the plate is sticked to the rear of the appliance). 24 2º The meter, the fuses, the wiring and the socket outlet can support the max. 3º The socket base and the plug must fit in adequately without any reducing interposition, multiple outlets or adapters. If necessary replace the socket outlet by an adequate one. (Never touch the washing machine or any electric appliance while standing on a wet floor or being barefoot. ) 90 cm. Max. i YOUR WASHING MACHINE 1 Washing powder dispenser 2 On/of lamp 3 Option buttons 4 Temperature selector 5 Program selector 6 The door 7 Filter 8 Nivelation 1 FLS - 461C 345 2 9 10 11 12 13 3 2 1 13 12 1 2 2 3 4 5 6 7 8 11 10 9 90° 30° 4 80 ° 8 The products dispenser Symbols Prewash Wash Smooth AL020 Bleach 8 7 6 5 70° 60° 50° 40 ° 6 7 25 DESCRIPTION OF THE CONTROLS Control panel 1. Washing powder dispenser The dispenser is provided with 4 compartments marked with the following symbols: Prewash: symbol shows the compartment for the prewash detergent. Bleach: symbol shows the compartment for the bleaching additives. 4. 1/2 load button (only for programmes 1 to 4) Pressing this button before starting the intense program there will be one rinse less which leads to energy and water saving. 5. Temperature selector This control allows you to select the temperature of the washing cycle in accordance with the kind of clothes to be washed. Turn the control until the required temperature coincides with the marker. On the program table you will find the most apropriate temperature for each kind of washing. "NO SPINNING" button (only for programmes 1 to 6) Pressing this button before starting the "intense" washing programmes all spinnings will be excluded. Program selector To select the required program turn the control clockwise until the marker on the top coincides with the number of the required program (reference mark on the control panel). If at any chance you pass by the required number NEVER TURN THE CONTROL ANTICLOCKWISE just continue clockwise until the required number is reached again. 26 OPERATING SEQUENCE i Before executing the first wash with clothes we recommend to carry out the cleaning of the drum and the barrel by a special wash, without clothes. Pour a dose of detergent in the tray department corresponding to "Wash". Wait, at least, three minutes, after the light goes off, before opening the door of the washing machine. 1. Loading the washing machine Load the laundry loosely, alternating large items with small ones. Do not overload the washing machine, but always try to use its utmost capacity in accordance with the type of fabric. Once the machine is working and you wish to add any item you must stop the program. P0004 2. Dose the additives If you wish to use additives enter the softener in the compartment with the symbol and the bleacher in the compartment with the symbol Never exceed the MAX level. 4. Select the temperature Tur n the dial clockwise to the desired temperature. AL022 5. Select the program Turn the dial clockwise until the marker reaches the desired program. 27 6. [. . . ] Wait, always, till the washing program is over and there is NO WATER IN THE BARREL. When you replace the unloading filter in its place, make sure that it is correctly positioned and tight, in order to avoid water leakage or that children may take it off. AL011 P0040 The water inlet hose filter If it takes longer to fill up the washing machine it is time to check the water inlet hose filter it may be clogged. Remove the filter from the electrovalve and clean it with a hard bristle brush and replace it. Screw on the nut thoroughfully. P0090 P0021 34 SERVICING Before contacting your local Service Force Centre, check your machine against the simple maintenance guidelines given below. Problem The appliance does not start up Possible solution · · · · · · · · · · · · · · · · · · Check if the door is closed properly. [. . . ]