User manual YAKUMO TFT 15 AL

[. . . ] 4 4. 6 OSD menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. 7 Self test pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 8 Safety protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 9 Preset modes timing chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of the television receiver and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the monitor on a bed, sofa, rug, or other similar surface. This monitor should not be placed in built-in installation such as a bookcase unless proper ventilation is provided. Do not locate this monitor where the cord will be abused by persons working on it. Never push objects of any kind into this monitor through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fore or electric shock. Do not attempt to service this monitor yourself since opening or removing covers may expose you to dangerous voltage or other hazards. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under the following : a. When the monitor exhibits a distinct change in performance this indicated a need for service. Introduction Chapter 1 Introduction 1. 1 Features Multi-scanning at horizontal frequencies of 30~60KHz(15"), 30~80KHz(17") and vertical frequencies of 60Hz to 75Hz. Compatible with standard IBM VGA, extended VGA, super VGA, IBM XGA modes, as well as VESA resolution standards. Microsoft Windows 9x/2000/XP compatible & VESA Display Data Channel (DDC) 1/2B compatible. 1. 2 Checking List Please make sure the following items are included with your LCD monitor. Your monitor AC Adapter AC power cord VGA Signal cable Audio cable If any of these items are missing, please contact with your dealer for technical support and custom service. Note: Be sure to save original box and all packing material for transport in future if the monitor need, 1 Chapter 2 Installation 2. 1 Connect your monitor to computer 1 Turn off your computer and unplug its power cable. Installation 2 Connect the power cable for your monitor to the DC adapter and connect the adapter the DC power jack on the back of your monitor. 4 Connect the DVI or D-Sub 15Pin signal cable to the video port on the back of your computer 5 Plug the computer and monitor power cables into a nearby outlet. 6 Turn your computer and monitor on, if your monitor display an image, you have successfully installed the monitor. If the monitor does not display an image, check all the connections. 1 2 3 Connecting the monitor to the computer and the power supply 2 Over view of your monitor Chapter 3 Over view of your monitor 1 2 2 3 4 5 3. 1 Front panel over view MENU DO WN UP AUTO POWER 1. DVI/VGA IN 3 Chapter 4 4. 1 Power ON/OFF Switch OPERATION Direct ­ Access Features OPERATION Direct ­ Access Features This button is used to turn the monitor on and off. NOTE : The ON/OFF switch does not disconnect the device from the main voltage. To completely disconnect the mains voltage, please remove the power plug from the socket. 4. 2 Power indicator This indicator lights up blue/green when the monitor operates normally. If the monitor is in power saving mode, this indicator change to amber when monitor is turn off, this indicator change to dark. 4. 3 Auto Auto adjust function : Press AUTO button and release, the auto adjust display mode will tune to the utmost performance according to VGA setting. , Change mode Function : Press AUTO button 2 seconds and release to enter signal search mode. , You could choose among signals by pressing and release AUTO button. 4. 4 Volume This feature adjust the DOWN button to decrease the volume and adjust UP button to increase the volume. 4. 5 Menu Features The following features can all be accessed using your monitor on screen menu system. Making adjustments to a feature, pushing the exit button to turn off the menu. [. . . ] exit To exit the menu. 5 OPERATION Direct ­ Access Fvzeatures advanced 1. cool This control adjusts the color temperature of the screen image, this item are preset by factory, you can not adjust these setting. warm The performance is reddish and closer to paper white user You can adjust the individual color intensity by yourself. Increase or decrease red, green or blue depending upon which is selected. [. . . ]