User manual YAKUMO 32 LCD TV 81J

[. . . ] Handbuch Manual Manuel D GB F E I Yakumo 32" LCD TV LCD TV Manual Explanation of WARNING Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence dangerous voltage within the inside of the product that may be sufficient level to constitute a risk of electric shock. English The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions. Safety instructions 1) 2) 3) 4) 5) 6) 7) 8) Read these instructions. Keep your Yakumo 32" LCD TV away from moisture, excessive dust and any heat sources, such as radiators, heat registers, stoves, or any other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] Press a coloured button corresponding to the coloured brackets on the screen for page number storage. Enter the Teletext page number using the 0 ~ 9 digit buttons (enter three digits). Press the STORE button to memorize the page numbers you require. 6 Manual HOLD button Press this button to remove the information from the display and stop the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed the stop symbol is displayed at the left-top corner of the screen and the automatic changing is inhibited. English nglish SIZE button Select double height text under Teletext mode for full screen. Press this button again to return to the normal display. LANGUAGE button Press this button to select the language of Teletex function between English, Cyrillic and Arabic. SUBCODE button When a selected Teletext page with hidden sub pages or timed pages, these pages can be seen by the following manner: Press the sub code button. (Headphone sold separately) Headphone (not supplied) 10 Manual Connecting with PC Audio In cable/ D-SUB Audio-IN Connect the Audio In cable (green) from audio output of your computer to the audio input terminal (green) of the Yakumo 32" LCD TV. PC English nglish PC Audio Out Connection (not supplied) Connecting with the power cord Connect the power cord to the power cord connector on the back of your Yakumo 32" LCD TV, and plug the other end of the power cord into a correctly grounded electrical outlet. AC Switch Switch to ON AC wall Switch 11 Manual BASIC OPERATION To operate your Yakumo 32" LCD TV, you may use the TV remote control or upper panel buttons to select input source, change channels, or adjust volume. Turning on the Yakumo 32" LCD TV Before using the Yakumo 32" LCD TV: 1. Turn on Main Power Switch, located on the rear of the cabinet (If the Yakumo 32" LCD TV will not be used for a long period of time, please turn it off). Power On/Off To turn the Yakumo 32" LCD TV on/off : Press POWER button on the bottom of the cabinet or press POWER key on your remote control to turn on/off the TV. Select input source Press SOURCE key and use to select the required input source between D-SUB, HDMI, TV, Video, S-Video, Component, SCART1, SCART2, SCART2-SV. . . If you want to restore volume, press MUTE again, or press VOL directly. Channel Select Press number keys, PROGRAM keys, or CH-/+ buttons to select the desired channels. The function is used to automatically shut off the Yakumo 32" LCD TV after a preset period of time passed. PIP and POP Screen Display PIP Screen and POP Screen PIP screen and POP screen allow you watch two screens from different sources at the same time. Press PIP or POP key on remote control to display main and sub-screen at the same time. 12 English Manual PIP Screen : POP Screen English nglish PIP/POP Input Source Select 1. SOURCE to select input source for sub-screen as following, Main Screen D-SUB/ TV/ Video/ S-Video/ SCART1/ SCART2/ SCART2-SV D-SUB/ HDMI/ Component Input Source of Sub-Screen D-SUB/ HDMI/ Component TV/ Video/ S-Video / SCART1/ SCART2/ SCART2-SV 2. Swap main and sub screen of PIP/ POP Press SWAP to exchange main-screen to sub-screen. PIP Position To setup the position of sub-screen. Adjust Volume of Sub-screen Press V+ and V- to adjust volume of sub-screen. Select Program for Sub-screen Press P+ and P- to select the program of sub-screen. (TV mode only) Sound Sound Mode Select Continue to press SMART. S to select the sound mode between Movie, Music, Speech, and User. Sound Source Select Continue to press M S Sound to select the sound source between main screen and sub-screen. [. . . ] Clock: To adjust delay time of clock in order to reduce the noise of picture. Phase: To adjust delay time of phase in order to reduce the noise of picture. 18 Manual Colour Mode: To adjust colour temperature. English 1. When select "User, " it allows you separately adjust the colour of red, green, and blue. Reset: Press ENTER to reset all the settings in PC page. OSD Menu --To setup OSD window It is active in all input sources except HDMI source. H-Position: To adjust the OSD horizontal position with . [. . . ]