User manual YAESU FL-2100Z

[. . . ] 12 LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 To Append an Alpha-numeric "Tag" to a Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Storing Independent Transmit Frequencies ("Odd Splits") . . . 37 Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press and hold in the [V/M] key for 1/2 second, then rotate the "Main" band DIAL knob to select the Memory Bank ("BANK1" ~ "BANK10" ) you want as the Memory Bank for this channel. Press and hold in the [SET] key for 1/2 second to copy the memory channel data into the Memory Bank. The PMS memory channel (L1/U1 through L10/U10) does not assign to the memory bank. Set the radio to the Memory mode by pressing the [V/M] key, if necessary. Press and hold in the [V/M] key for 1/2 second, then rotate the "Main" band DIAL knob to select the Memory Bank ("BANK1" ~ "BANK10" ). In the Memory Bank mode of operation, you can only select memory channels in the current memory bank. To change the Memory Bank to another Bank, press and hold in the [V/M] key for 1/2 seconds, then rotate the "Main" band DIAL knob. To exit from Memory Bank operation, press and hold in the [V/M] key for 1/2 second, then rotate the "Main" band DIAL knob to select "ALL. MEM, " then press the [SET] key momentarily. In the Memory Bank mode, recall the memory channel to be deleted from the Memory Bank. Press and hold in the [V/M] key for 1/2 second, then press and hold in the [SET] key for 1/2 second to delete the Memory Channel from the Memory Bank. Memory Only Mode Once memory channel programming has been completed, you may place the radio in a "Memory Only" mode, whereby VFO operation is impossible. This may be particularly useful during public-service events where a number of operators may be using the radio for first time, and ultimate simplicity of channel selection is desired. The scanner will then resume according to the Scan-Resume mode selected in the previous section. To cancel scanning, press the [SCN] key momentarily again (or press the microphone's PTT key). 1) When you start scanning, the FL-2100ZR will be changing frequency in the upward direction. If you want to change direction of the scan while it is underway, rotate the DIAL knob one click in the opposite direction (in this case, one click counterclockwise). You'll see the scanner turn around and change frequency downward!2) Pressing and holding in the microphone's [UP] or [DWN] key will cause the scanner to sweep frequencies only on the current band. If you would like the scanner not to be restricted to the current band, you may change Menu #4 (BAND) to allow the scanner to hop to the low edge of the next-highest band when the VFO frequency reaches the high end of the current band (or vice- versa). See page 61 for details. FL-2100ZR Operating Manual 39 SCANNING MEMORY SCANNING Memory scanning is similarly easy to initiate: 1. Set the radio to the Memory mode by pressing the [V/M] key, if necessary. As with VFO scanning, the scanner will halt on any signal encountered that is strong enough to open the squelch; it will then resume scanning according to the Scan-Resume mode set previously. To cancel scanning, press the [SCN] key again (or press the microphone's PTT key). How to Skip (Omit) a Channel During Memory Scan Operation Some continuous-carrier stations like a Weather Broadcast station will seriously impede scanner operation if you are using the "Carrier Drop" Scan-Resume mode, as the incoming signal will not pause long enough for the transceiver to resume scanning. [. . . ] Two seconds after the carrier has dropped because the other station(s) ceased transmission, the scanner will resume. Menu #35 [SCAN M] Function: Selects the Memory Scan mode Available Values: MEM/MSM Default: MEM MEM: Enables Memory Scanning on all memory channels. MSM: Enables Memory Scanning on "flagged" Memory Channels only. Available Values: 0. 00 - 99. 95 MHz (50 kHz step) Default: Depends on the band of operation. [. . . ]