User manual WOXTER I-CUBE 700 DATASHEET

[. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Images which are not corrected properly can appear too white or too dark, so controlling the gamma properly can have a huge The options are: {NATIVE} / {2. 2} / {2. 4} / {S GAMMA}. NOTE: This item is functional for HDMI(Video mode), S-Video, Video, and YPbPr inputs only. The display converts a 24 frames-per-second (24 fps) input signal format to DVD video signal format. Once this function is enabled, it is recommended that you set the {SCAN CONVERSION} function to {PROGRESSIVE}. PICTURE RESET Reset all settings in the Picture menu to factory preset values. V POSITION Press the [ ] button to move the image up, or [ ] to move the image down. CLOCK PHASE Adjust to improve the focus, clarity and stability of the image. ZOOM MODE The pictures you receive may be transmitted in 16:9 format (wide screen) or 4:3 format (conventional screen). The 16:9 pictures sometimes have a black band at the top and bottom of the screen (letterbox format). The following zoom modes are available for: PC mode: {FULL} / {NORMAL} / {CUSTOM} / {REAL}. Video mode: {FULL} / {NORMAL} / {DYNAMIC} / {CUSTOM} / {REAL}. FULL This mode restores the correct proportions of pictures transmitted in 16:9 using the full screen display. NORMAL The picture is reproduced in 4:3 format and a black band is displayed on either side of the picture. 4. 2. 2. SCREEN menu SCREEN AUTO SETUP AUTO ADJUST H POSITION V POSITION CLOCK CLOCK PHASE ZOOM MODE CUSTOM ZOOM H RESOLUTION V RESOLUTION INPUT RESOLUTION SCREEN RESET OFF 50 50 2200 66 FULL 1920 1080 DYNAMIC Fill the entire screen by stretching 4:3 pictures non-proportionally. CUSTOM Choose to apply the custom zoom settings in the Custom Zoom submenu. 1 2 3 PIP REAL This mode displays the image pixelby-pixel on screen without scaling the original image size. :SEL SET :NEXT EXIT :RETURN MENU :EXIT MENU CUSTOM ZOOM You can use this function to further customize the zoom settings to suit the image you want to display. SCHEDULE This function allows you to program up to 7 (seven) different scheduled time intervals for the display to activate. Which input source the display will use for each scheduled activation period. NOTE: You should set up current date and time in {DATE AND TIME} menu before using this function. Press [SET] button to enter the submenu. Select or leave an empty "__" for both the hour and minute slot if you do not want to use this power-on or power-off schedule. 3 INPUT-SOURCE selection: Press [ ] or [ ] button to select an input source. If no input source is selected, the input source will remain the same as last selected. DATE schedule: Press [ ] button to select which day in a week this schedule item will be take effect, and then press the [SET] button. 4 4. For more schedule settings, press [EXIT] button and then repeat the steps above. A check mark in the box next to the number of the schedule item indicates that the selected schedule is in effect. NOTES: The {EVERY DAY} selection in a schedule item takes priority over the other weekly schedules. If the schedule overlap, the scheduled power-on time takes priority over scheduled power-off time. If there are two schedule items programmed for the same time, the highest numbered schedule takes priority. [. . . ] How long the warranty is effective: ViewSonic LCD Commercial Displays are warranted for 3 years for all parts excluding the light source and 3 years for labor from the date Who the warranty protects: What the warranty does not cover: 2. Damage, deterioration or malfunction resulting from: instructions supplied with the product. Any product exhibiting a condition commonly known as "image burn-in" which results when a static image is displayed on the product for an extended period of time. Removal, installation, one way transportation, insurance, and set-up service charges. [. . . ]