User manual WHIRLPOOL WED8510FW DIMENSION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WED8510FW. We hope that this WHIRLPOOL WED8510FW user guide will be useful to you.


WHIRLPOOL WED8510FW DIMENSION GUIDE: Download the complete user guide (397 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WED8510FW USE & CARE GUIDE (4485 ko)
   WHIRLPOOL WED8510FW WARRANTY INFORMATION (150 ko)
   WHIRLPOOL WED8510FW USE & CARE GUIDE (4485 ko)
   WHIRLPOOL WED8510FW INSTALLATION GUIDE (9541 ko)
   WHIRLPOOL WED8510FW WARRANTY INFORMATION (150 ko)
   WHIRLPOOL WED8510FW VENTILATION SPECIFICATION (1518 ko)

Manual abstract: user guide WHIRLPOOL WED8510FWDIMENSION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Gas and Electric Dryer PRODUCT MODEL NUMBERS WED8000D, WED8500D, WGD8000D, WGD8500D, WED8700E, WGD8700E, WED8510F Side view 561/4" (1428 mm) 3213/16" (821 mm) Door Opened Door Closed Back view 29" (737 mm) 57/8" (150 mm) 4213/16" (1987 mm) 41/2" (115 mm) 3" (77 mm) 13/8" 141/2" (35 mm) (370 mm) 31/2" (93 mm) 1" (25 mm) 113/8" 35/8" (289 mm) (93 mm) NOTE: Leveling legs 1" (25 mm) (3. 6 washer capacity) or 1½" (38 mm) (3. 8 washer capacity) depending model. Bottom view Minimum Required Spacing 14" max (356 mm) 81/2" (218 mm) 143/8" (365 mm) NOTE: Most installations require a minimum of 6" (152 mm) clearance behind dryer for exhaust vent with elbow. [. . . ] An individual manual shutoff valve must be installed within 6 ft (1. 8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223. 1. ELECTRICAL REQUIREMENTS - Gas models only A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. A time-delay fuse or circuit breaker and a separate circuit are recommended. ELECTRICAL REQUIREMENTS - Electric models only To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz. , AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. Connect to an individual branch circuit. WATER (STEAM MODELS ONLY) REQUIREMENTS The dryer must be connected to the cold water faucet using new inlet hoses. Damage to the coupling can result. VENTING REQUIREMENTS Exhaust venting: Exhaust your dryer to the outside. Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust. Determine vent length and elbows needed for best drying performance: ■■ Use following Vent System Chart to determine type of vent material and hood combinations acceptable to use. Exhaust hoods: Recommended Styles: NOTE: Do not use vent runs longer than those specified in Vent System Chart. Exhaust systems longer than those specified will: ■■ Shorten life of dryer. [. . . ] For complete details, see Installation Instructions packed with product. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WED8510FW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WED8510FW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.