User manual WHIRLPOOL UXT4030ADS INSTALLATION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL UXT4030ADS. We hope that this WHIRLPOOL UXT4030ADS user guide will be useful to you.


WHIRLPOOL UXT4030ADS INSTALLATION GUIDE: Download the complete user guide (2002 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL UXT4030ADS WARRANTY INFORMATION (94 ko)
   WHIRLPOOL UXT4030ADS DIMENSION GUIDE (180 ko)
   WHIRLPOOL UXT4030ADS WARRANTY INFORMATION (94 ko)

Manual abstract: user guide WHIRLPOOL UXT4030ADSINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ■ Use this unit only in the manner intended by the manufacturer. –  Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. –  Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. [. . . ] Prepare Range Hood Align the exterior edge of the mounting brackets with the exterior edges of the upper cabinet. –  ■ Set the range hood on its back on a covered surface. Using a flat-blade screwdriver, remove the appropriate power supply knockout. Drill Electrical Opening Lift the range hood into place and insert the mounting bracket tabs through the slots in the back of the range hood. Using a 1¹⁄₄" (3 cm) drill bit, drill the hole in the dot marked previously at the electrical strain relief. OPTIONAL: Using a ¹⁄₈" (3 mm) drill bit, drill pilot holes for the dots marked previously at each mounting tab at an approximate 45° angle in an upward direction. Prepare Range Hood Vents and Mounting Tabs x2 90˚ C B B A Hold the range hood firmly in place with one hand and bend each mounting tab (A) upward approximately 90°. 2 x 16 mm) truss-head screw into the mounting tab (C) on each side of the range hood as shown in the inset. –  ■ Non-vent (Recirculating) Installations Remove the (2) T10®† Torx® screws and remove the top, front rectangular vent cover (B). Mount Range Hood ■ Option 1 - Direct Wire Installations Use a UL Listed/CSA Approved wire connector and connect the 2 white wires (A) together. Use a UL Listed/CSA Approved wire connector and connect the 2 black wires (B) together. –  Lift the range hood into place, positioning the rear slots over the mounting brackets. Using a Phillips screwdriver, push on the screws that are started into the top mounting tabs and bend the tabs against the cabinet side walls. For direct wire installations, run the home power supply cable according to the National Electric Code or CSA standards and local codes and ordinances. There must be enough wiring from the fused disconnect (or circuit breaker) box to make the connection in the range hood electrical terminal box. OPTIONAL: If you prefer, bend the rear tabs against the rear of the range hood and attach to the wall using #8-18 x ⁵⁄₈" (4. –  ■ ■ Connect the green (or bare) ground wire (C) from the power supply to the green ground screw in the electrical box and tighten the screw securely. Option 2 - Power Cord Kit Installations For optional power cord kit installations, follow the instructions supplied with the power cord kit. See the “Assistance or Service” section for information on ordering. NOTE: Use only with range hood cord connection kits that have been investigated and found acceptable for use with this model range hood. Complete the Installation ■ Install a 120V, 75W maximum, incandescent light bulb with E12 base. See “Replacing the Incandescent Light Bulb” in the “Range Hood Care” section. [. . . ] The cost of repair or replacement under these excluded circumstances shall be borne by the customer. dISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES , INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE , ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL UXT4030ADS




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL UXT4030ADS will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.