User manual WACOM DTF-720

[. . . ] www. wacom. com DTF-720 interactive pen display Installation Guide & User's Manual Wacom DTF-720 interactive pen display Installation Guide & User's Manual English version 1. 0, August 12, 2005 Copyright WACOM Company, Limited, 2005 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. [. . . ] · When toggled to your computer's mouse settings (mouse mode), the screen cursor is not directly "linked" to the pen tip and is positioned like a mouse, requiring a "pick up and slide" motion to move the cursor on the screen. On multiple monitor systems, mouse mode will allow you to access the other monitor(s) with your pen. Customizing Page 23 Adjusting the LCD monitor Factory presets, multi-sync, and user settings Factory presets: For optimal display quality, set your video card to the DTF-720's native resolution of 1280 x 1024 pixels. Multi-sync: The DTF-720 attempts to automatically synchronize to the incoming signal. Multi-sync will function when the horizontal frequency is between 30 to 80 kHz and the vertical frequency is between 50 to 75 Hz. If the DTF-720 does not automatically synchronize with the incoming signal, you can use the On Screen Display (OSD) RESET AUTO ADJUST option to initiate display synchronization. Further screen display adjustments can be manually made using the OSD controls. User settings: When you manually set the display using the OSD function, the settings are stored within the DTF-720 for use the next time the unit receives a similar signal. This is applicable to all display modes. Working with on screen display settings The DTF-720 is equipped with an On Screen Display (OSD) function. The OSD function enables you to adjust and optimize a variety of display settings at the touch of a button. The OSD controls are located on the upper left edge of the unit. ­ + ENTER button Activates or deactivates the selected OSD menu option. Menu button Opens or closes the OSD menu. Selection buttons Use these buttons to select an option that can be activated when you press the ENTER button. After activating a selected option, press the + button to increase a selected item value, and press the ­ button to decrease it. The basic process for working with the OSD is as follows: · Press the MENU button to open the OSD main menu. When the option you want to adjust is highlighted, press the ENTER button. The current settings and adjustment sub-menu for that option will appear. If you make changes to the display appearance and cannot return to the original settings, use the RESET RECALL option to return the DTF-720 to its original factory defaults. Customizing Page 24 When you open the On Screen Display, the following menu option icons are displayed: CONTRAST. Provides two options: Use AUTO ADJUST to reset only the image parameters. Selecting the EXIT icon exits the RESET window without resetting anything. Select to increase or decrease the backlight brightness level. LANGUAGE. Provides color temperature settings for 9300°, 6500°, and 5000° Kelvin. When DIRECT is selected, the BRIGHTNESS and CONTRAST settings are also set to DIRECT and cannot be adjusted manually. The USER option enables you to adjust Red, Blue, and Green independently. In the user adjustment COLOR window, change Red, Green, or Blue to calibrate color. icon Customizing Page 26 Adjusting pitch and phase Some computers and video cards may not allow the multi-sync function to fully work when the DTF-720 is first connected. [. . . ] Wacom cannot guarantee you uninterrupted service or the correction of any errors. Upon discovery of a defect in the product, except in the Software, within the Warranty Period, you should contact Wacom Technical Support via telephone, email, or fax to obtain an RMA (Return Merchandise Authorization) number and instructions for shipping the product to a service location designated by Wacom. You should send the product, shipping charges prepaid, to the designated service location, accompanied by the return authorization number, your name, address and telephone number, proof of purchase date, and a description of the defect. Wacom will pay for return shipping by United Parcel Service or by an equivalent service as chosen by Wacom. [. . . ]