User manual VOLTA 4560 GRAPHITE GREY

[. . . ] 7 PRODUCT LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BACK LABEL 5 6 7 8 9 SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4560 GRAPHITE GREY PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SETUP LAN, WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] • MBS: Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent at the peak rate. Type the MBS, which is less than 65535 Encapsulation: • ISP: Select the encapsulation type your ISP uses from the Encapsulation list. If you select Routing in the Mode field, select PPPoA, 1483 Bridged IP, 1483 Router IP or PPPoE. PPPoE/PPPoA • User Name: Enter the user name exactly as your ISP assigned. • Password: Enter the password associated with the user name above. • Encapsulation: select Bridge in the Mode field, select either PPPoA or RFC 1483. • select Routing in the Mode field, select PPPoA, RFC 1483, ENET ENCAP or PPPoE. • Connection: The schedule rule(s) have priority over your Connection settings. • Always on: Select Always on Connection when you want your connection up all the time. • Connect on Demand: Select Connect on Demand when you don't want the connection up all the time and specify an idle time-out in the Max Idle Timeout field • Get IP Address: Choose Static or Dynamic • Static IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, 192. 168. 1. 254 (factory default). It allows you to set the router to act in “AP”, “Client” or “WDS” mode. To use RADIUS, enter the IP address of the RADIUS server, the RADIUS port (default is 1812) and the shared secret from the RADIUS server. Please refer to “Authentication RADIUS Server” setting below for RADIUS setting. Personal (Pre-Shared Key) – Pre-Shared Key authentication is based on a shared secret that is known only by the parties involved. To use WPA Pre-Shared Key, select key format and enter a password in the “Pre-Shared Key Format” and “Pre-Shared Key” setting respectively. Pre-Shared Key You may select to select Passphrase (alphanumeric format) or Format Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Pre-shared Key. For example: Passphrase: ”iamguest” Hexadecimal Digits: “12345abcde” Pre-Shared Key Please enter 8-63 characters as the “Pre-Shared Key”. Authentication Enter the port (default is 1812), the IP address and the RADIUS Server password of external RADIUS server are specified here. When you finish, click ‘save’ to save the settings made and restart the router so the settings will take effect after it reboots. Wireless ACL This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Parameter Active Actions Description Choose to either Enable – Enabled the Wireless Access Control Disable – Disable the Wireless Access Control Allow – Only allow the wireless clients with the MAC Address you have specified can access to the router. Deny – The wireless clients with the MAC Address you have specified will be denied accessing to the router. MAC Address Enter the MAC Address of the wireless clients for the filtering control. When you finish, click ‘save’ to save the settings made and restart the router so the settings will take effect after it reboots. 13 Advanced Settings The advanced settings pages allow users to modify the more complex features of this device. Advances wireless This page allows advanced users who have sufficient knowledge of wireless LAN. These setting shall not be changed unless you know exactly what will happen for the changes you made on your router. Parameter Beacon Interval Fragmentation Threshold RTS Threshold Description The interval of time that this wireless router broadcast a beacon. The range for the beacon period is between 20 and 1024 with a default value of 100 (milliseconds). Fragment Threshold specifies the maximum size of packet during the fragmentation of data to be transmitted. [. . . ] - IP/Mac Filter - Application filter - URL block IP Filter Rule Editing • IP Filter Rule Index: This is item number • Active: Select Yes from the drop down list box to enable IP filter rule. • Source IP Address: The source IP address or range of packets to be monitored. • • Subnet Mask: It is the destination IP addresses based on above destination subnet IP Source Port Number: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application. Default is • • • • • set from range 0 ~ 65535. [. . . ]