User manual VIOLET DESIGN AMETHYST DESCRIPTION

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual VIOLET DESIGN AMETHYST DESCRIPTION. We hope that this VIOLET DESIGN AMETHYST DESCRIPTION user guide will be useful to you.


VIOLET DESIGN AMETHYST DESCRIPTION : Download the complete user guide (2264 Ko)

Manual abstract: user guide VIOLET DESIGN AMETHYST DESCRIPTION

Detailed instructions for use are in the User's Guide.

[. . . ] They possess very fast impulse transient response without sound coloration or low frequency reduction, as well as the ability to handle louder sound pressure levels. [. . . ] The internal phantom powered preamplifier is a fully discrete Class 'A' transformerless circuit which provides high output, flat audio response and ulta-low distortion and noise. The Amethyst Vintage has a grey/blue body and uses a dual large-diaphragm, center terminated dual back plate capsule which provides a classical, wide-spectrum, vintage microphone sound. Both models have a unidirectional cardioid polar pattern with minimal proximity effect and are linear over the wide frontal incidence angle. The Amethyst Standard is particularly recommended for percussion and stringed instruments. For vocal applications The Amethyst Standard is more oriented for a male voice and The Amethyst Vintage for a female voice. The internal amplifier and capsule are hard to overload and are well suited for close miking of vocals. SPECIFICATIONS FREQUENCY CHART: THE AMETHYST DESCRIPTION DESCRIPTION +4 Transducer type: electrostatic Operating principle: pressure gradient standard db O Diaphragm's active diameter: 1" (26mm) vintage Frequency range: 20 Hz to 20 kHz Polar pattern: cardioid -4 20 30 50 Output impedance: 50 ohms Rated load impedance: 1000 ohms Suggested load impedance: > 500 ohms Sensitivity at 1000 Hz into 1000 ohms load: 21 mV/Pa S/N Ratio (CCIR 468-3 weighted): 76 dB S/N Ratio (DIN/IEC 651 A-weighted): 87 dB-A Equivalent noise level DIN/IEC A-weighted: 7 dB-A Maximum SPL for 0. 5% THD at 1000 ohm load: 134 dB Dynamic range of the microphone preamplifier: 127 dB Phantom power voltage (on XLR pins 2 & 3): 48V (±4V) Current consumption: < 2 mA Output connector: 3-pin XLR male Signal polarity: pin 2 in phase Dimensions & Weight: 6. 6" (h) x 2. 5" (w) / 12. 3 oz. [. . . ] The internal amplifier and capsule are hard to overload and are well suited for close miking of vocals. SPECIFICATIONS FREQUENCY CHART: THE AMETHYST DESCRIPTION DESCRIPTION +4 Transducer type: electrostatic Operating principle: pressure gradient standard db O Diaphragm's active diameter: 1" (26mm) vintage Frequency range: 20 Hz to 20 kHz Polar pattern: cardioid -4 20 30 50 Output impedance: 50 ohms Rated load impedance: 1000 ohms Suggested load impedance: > 500 ohms Sensitivity at 1000 Hz into 1000 ohms load: 21 mV/Pa S/N Ratio (CCIR 468-3 weighted): 76 dB S/N Ratio (DIN/IEC 651 A-weighted): 87 dB-A Equivalent noise level DIN/IEC A-weighted: 7 dB-A Maximum SPL for 0. 5% THD at 1000 ohm load: 134 dB Dynamic range of the microphone preamplifier: 127 dB Phantom power voltage (on XLR pins 2 & 3): 48V (±4V) Current consumption: < 2 mA Output connector: 3-pin XLR male Signal polarity: pin 2 in phase Dimensions & Weight: 6. 6" (h) x 2. 5" (w) / 12. 3 oz. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE VIOLET DESIGN AMETHYST DESCRIPTION




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual VIOLET DESIGN AMETHYST DESCRIPTION will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.