User manual VIEWCAST NIAGARA 2120 QUICK GUIDE

[. . . ] The following steps in this Quick Start Guide will help you set up and configure your Niagara 2120 so you can begin streaming or capturing video as quickly as possible. The Niagara 2120 Web interface allows quick and easy access to the operational features of the Niagara 2120. You must modify any advanced setup options of the Niagara 2120 encoders through this interface before running an encoder session. Complete the following steps to begin operating the Niagara 2120: 2) Press Power on the front panel to start the Niagara 2120. [. . . ] Once connected to a network, you should be able to access the built-in Web server by browsing to the unique machine name (serial number). If you do not have a DHCP network or you cannot connect to the Niagara 2120 through its DNS name, you can connect a monitor, mouse, and keyboard directly to the Niagara 2120 to USB ports. From the desktop, launch Internet Explorer and proceed through the next section. 8) To view available encoder profiles, from the menu bar click Encoders > All Encoders. 6) The system may re-display the Admin Log In window again once you submit the date, time, and video standard fields. 7) This time when you enter your valid user name and password, the system displays the Welcome window and Niagara 2120 Main Menu. You may connect analog component, composite, or S-Video to the Niagara 2120 as follows: Component BNC Input , , The Niagara 2120 includes analog component video BNC inputs. 2. Connect video and audio sources Video Composite BNC Input The Niagara 2120 includes a BNC-to-RCA adapter so you can connect a composite RCA video source to the BNC connector labeled CVBS-Pb. 4. First start setup The first time you power on the Niagara 2120, the system takes a few moments to boot up. From a separate computer on the same network as the Niagara 2120, launch a Web browser such as Internet Explorer and enter the serial number or IP address of your Niagara 2120. The serial number is on the bottom of the appliance in the format gf10xxxxxx. 1) Check to ensure you connect all devices (power cords, video and audio sources, etc. ) to the Niagara 2120. Click Edit to the left of the Flash encoder to open the Encoder Properties window. Check to ensure the video, audio, and streaming settings for the encoder profile match your hardware setup using the Video, Audio, and Output tabs. You may start a stream from the Encoders window by clicking the red circled Stop button in the Streaming column. Continued on back © 2010 ViewCast Corporation. ViewCast®, Niagara® (and design)TM are registered trademarks of ViewCast Corporation or its subsidiaries. Product specifications and availability may change without notice. USA | 3701 W. Plano Parkway, Suite 300 Plano, Texas 75075-7840 972-488-7200 800-540-4119 UK | Worting House Church Lane Basingstoke Hampshire RG23 8PX U. K. +44 1256 345610 l l l l l Contact ViewCast Technical Support at support@viewcast. com. 40-03265-02-A Niagara® 2120 Quick Start Guide 4. First start setup continued 10) On the Video tab, set video Input to Composite. The Niagara 2120 Front Panel J: Remote Control I: Alarm/Status Indicator 11) Click the Audio tab and set audio Input to Unbalanced. K: Video Confidence Indicator Figure 1. Niagara 2120 Front Panel A: Power Button and Indicator Light 12) To enable Live Flash streaming, ensure the Enable Streaming box is selected. [. . . ] · This control changes the volume on the headset output only. Alarm/Status Indicator Remote Control Volume Button (Up/Down) 2. Press and release after the second set of 10 LEDs start to light (approximately 4 to 6 seconds) to keep all set profiles and restore the Niagara 2120 operating system. NOTE:The lights on the volume indicator will illuminate in one-second intervals, but do NOT progress all the way to the far right. · This indicator illuminates when a system alert occurs. · Displays to indicate a remote user. · Video encoding status (active). Video Confidence Indicator · A remote user is accessing the Niagara 2120 across the network. 3. Press and hold for approximately 10 seconds until all 20 LEDs remain lit to restore the Niagara 2120 to complete factory defaults. Warning!Option 3 deletes all previously set profiles. © 2010 ViewCast Corporation. ViewCast®, Niagara® (and design)TM are registered trademarks of ViewCast Corporation or its subsidiaries. Product specifications and availability may change without notice. USA | 3701 W. [. . . ]