User manual VENOM 4083 MINI TRAIN

[. . . ] HOLD) Displays the transmitting mode (See 2. 1 SYSTEM / MOD (MODULATION) The current position of the steering and throttle trims setting are displayed. PROGRAMMING MODE To enter programming mode from the Main Screen press the ENTER button on the transmitter. To save and exit from the sub menu press EXIT. 2. 1 FUNCTION / EPA (END POINT ADJUSTMENT) End Point Adjustment (EPA) - Used to set the maximum travel of the desired function from 0-120%. Can be used to set both directions of travel (fwd/bk & lft/rt) to adjust the overall range of movement or value. [. . . ] 5) Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to the Main Screen EXP Curve This feature is a simple exponential curve. Using the EXP feature will help smooth your throttle response for vehicles with a touchy throttle. 2) Select the "R" (rate) to set the throttle curve rate by pressing ENTER 3) Use the (+) to make the throttle rate more sensitive. Brake Adjustments This adjustment is the same for all three Throttle Curve types. 3) Press the EXIT button to return to the FUNCTION menu, and again to return to the main screen. CUR Curve This feature has three adjustable throttle rate points through the throttle range that can be independently adjusted. 2) Select the "R" (rate) to set the throttle curve rate by pressing ENTER. 4) Press enter to go to the (2) ­ 2nd point 5) Adjust the (2) point with the +/- buttons 6) Press enter and repeat for the (3) ­ 3rd point 7) Press enter and set the braking rate. Refer to the section on Brake Side adjustments in the EXP Curve section. VTR Curve This Feature is enables the user to make throttle curve steeper (or milder) in a specific range by allowing two different throttle curve rates by changing the curve switching point. Press EXIT again to return to the main menu. 5 2. 7 FUNCTION / ABS (ANTI-LOCK BRAKE SYSTEM) The ABS feature is just like a real car in that the brakes will pulse intermittently when they are applied to reduce the chance of a skid or in the case of a 4 Wheel Drive vehicle, it will reduce under steer. If a loss of signal should occur the receiver will adjust the steering or throttle or both to a preset value. 2) Use the +/- KEYS to highlight F/S and press ENTER 3) Press ENTER to select a setting 4) Use the +/- KEYS to change the value 5) Press EXIT to save and return to SYSTEM MENU, press EXIT to return to the FUNCTION MENU, press EXIT again to Main Screen. TERMS: EN-ENABLE, TH-THROTTLE, ST-STEERING, 2. 16 FUNCTION / NEUTRAL This function is used to calibrate the neutral center point of the of the Steering wheel or Throttle trigger. Press ENTER to calibrate the neutral Press EXIT TWICE to save and return to the FUNCTION menu. Note: Do not move the Steering wheel or Throttle trigger during the calibration process. 2) Use the +/- KEYS to highlight F/S and press ENTER 3) Press ENTER to select a setting 4) Use the +/- KEYS to change the value 5) Press EXIT to save and return to the FUNCTION MENU, press EXIT again to Main Screen. TERMS: EN-ENABLE, TH-THROTTLE, ST-STEERING, 11 2. 17 FUNCTION / SOUND This function is used to turn the beeping tones ON or OFF on the Transmitter. Press EXIT TWICE to save and return to the FUNCTION MENU. 2. 18 FUNCTION / RESET RESET - This function is used to reset the entire memory of the 4083 MINI TRAIN 2. 4. 2) Use the +/- KEYS to highlight the RESET box and press ENTER 3) Press ENTER to reset the 4083 MINI TRAIN 2. 4 transmitter memory 4) Press EXIT to save and return to SYSTEM MENU, press EXIT to return to the FUNCTION MENU, press EXIT again to Main Screen. 12 2. 19 FUNCTION / M_RES (MODEL RESET) Model Reset feature is used to reset a specific model memory slot back to factory default settings. Press EXIT TWICE to save and return to the FUNCTION menu. 2. 20 FUNCTION / TIMER Use the timer to monitor your race, lap times or test session. Use the +/- Keys to set the mode to UP_T or DN_T to activate the timer function. The UP_T setting will count up from zero to a user set time limit or a maximum of 99 minutes 30 seconds. The DN_T setting will count down to zero from a user set time limit or a maximum of 99 minutes 30 seconds. The timer will start on the first pull of the Throttle Trigger and will stop when full brakes are applied. [. . . ] If you believe a defect became evident only after operation, please contact us to discuss the situation. A dated & itemized sales receipt must accompany any product returned for warranty work. Before returning any product, please contact VenomTM Customer Service at 800-705-0620 to receive a Return Merchandise Authorization Number (RMA#). We guarantee this product to be free of manufacturing faults and material defects. [. . . ]