User manual UFREE SCOOTER POCKET BIKE PB-G03

[. . . ] 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 6 REMOVE AND REFIT THE FRONT WHEEL. FIG. 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 REMOVE AND REFIT THE REAR WHEEL . 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 REPLACEMENT OF SPROCKET -FK3. 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ENGINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 MINIBIKE SQ40A . FJG. 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 10 PARTS LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 12 FRONT AND REAR BRAKES . FIG. [. . . ] Open the petrol supply cock by turning the small lever into position "ON", Fig. Without turning the accelerating handle, pull gently twice the starting wire and by next quick pull start the engine. After a short engine run, put the choke lever back to position "A" and let the engine run about 1 min. Let the Minibike on the larking stand and, if need be, adjust the no-load speed to such a rate lest coupling should take along the no-load speed to such a rate lest coupling should take along the rear wheel. For adjustment use the adjustment screw N° 4 on the carburetor, Fig. Fuel cock RIDE After mounting the Minibike and slow turning the acceleration handle, you are starting your ride. Before braking, turn back the acceleration handle and depress slightly the front brake lever and then the rear brake lever. The Minibike engine will be switched off by pushing the red push-button of the stop switch on handlerods. After the first half-hour ride it is necessary to check the tightening of screws and nuts, especially of the engine. Check also the brake setting. 4 4 UFREE SCOOTER www. scooter-manufacturer. com PERIODIC MAINTENANCE Periodic maintenance is the best way to help the machine perform well, give longevity and provide safety and low cost operation. In addition, you will be spared from many-worries from self caused problems, resulting from poor maintinence or no maintinence. The chain free play should be (5 mm) (. 200in) After every ride clean the minibike carefully and keep it clean. After 1-hour of use, wash the air filter In air drying spirits and lubricate it with special oil for air filters. Wash the air filter in gas and lubricate it with special oil for an air filters to better catch the dust. Check the brake pads, the thickness of brake lining cannot be less than 1 mm (. 039 in). Check the state of the clutch pads - the thickness cannot be less than 1 mm (. 039in). CHAIN SETTING AND MAINTENANCE To set the chain tension, loosen the Nut (920. 011. 01) of the axel thru the rear wheel and the nut (914. 021. 01) of the rear Caliper anchor plate. The required chain tension (chain free play ) is (5 mm) (. 200in) and is performed by equal movement of the Axel adjustor plate (920. 009. 01) on the both sides of the rear wheel. When the adjustment is correct, tighten the Axel nuts and the Caliper holding nut Tighten the adjustor plate nuts both sides an extra nip, just to set them firmly. It is important to lubricate the chain regularly, to avoid excess wear and prolong effective lifetime. If chain replacement is necessary, check both chain Sprockets and if there is a need to change them do it together with the chain. CENTRIFUGAL CLUTCH PARTS REPLACEMENT Remove the chain guard by loosing two bolts M6 (916. 020. 01), Fig. [. . . ] Place the wheel on a hard surface and press the tire bead from the wheel rim in to the middle relief at centre of rim. Tire is ready to be removed from the rim at this time and is done in the conventional manner. After fitting new Tire and Tube (if necessary) to the rim, you can inflate 28 to 30 psi. Take care to check that the tire bead is fully seated in the rim bead edge You can new refit the wheel to the bike in reverse order to removing it Use Caution and recheck your work always. DISMANTLING AND MOUNTING OF AIR FILTER - FIG. [. . . ]