User manual TYAN THUNDER N6650EX S4992

[. . . ] S4992 /// Version 1. 0 S4992 Copyright Copyright © MiTAC International Corporation, 2008. No part of this manual may be reproduced or translated without prior written consent from MiTAC International Corporation. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD® , Opteron™, and combinations thereof are trademarks of AMD Corporation. AMI®, AMIBIOS®, and combinations thereof are trademarks of AMI Technologies. [. . . ] Since the KVM-over-IP Sever Management system memory is used to save all the information, the maximum number of possible log list entries is restricted to 1, 000 events. Every entry that exceeds this limit overrides the oldest one automatically. NFS Logging enabled Define a NFS server where a directory or a static link has to be exported to, in order to write all logging data to a file that is located there. To write logging data from more than one KVM-over-IP Sever Management card to only one NFS share, you have to define a file name that is unique for each device. When you 72 http://www. TYAN. com change the NFS settings and press the button "Apply", the NFS share will be mounted immediately. That means the NFS share and the NFS server must be filled with valid sources or you will get an error message. SMTP Logging enabled With this option the KVM-over-IP Sever Management is able to send Emails to an address given by the Email address text field in the Event Log Settings. These mails contain the same description strings as the internal log file and the mail subject is filled with the event group of the occurred log event. In order to use this log destination you have to specify a SMTP server that has to be reachable from the KVM-over-IP Sever Management card and that needs no authentication at all (<server ip>:<port>). SNMP Logging enabled If this is activated, KVM-over-IP Sever Management will send a SNMP trap to a specified destination IP address, every time a log event occurs. If the receiver requires a community string, you can set it in the appropriate text field. Most of the event traps only contain one descriptive string with all information about the log event. Only authentication and host power events have an own trap class that consists of several fields with detailed information about the occurred event. To receive this SNMP traps any SNMP trap listener may be used. 3. 5. 6. 9 SNMP Settings The following information is available via SNMP: 73 http://www. TYAN. com ‧ Serial number ‧ Firmware version ‧ MAC address / IP address / Net mask / Gateway of LAN interface ‧ Host system power state The following actions can be initiated via SNMP: ‧ Reset server ‧ Power on/off server ‧ Reset KVM-over-IP Sever Management The following events are reported by the KVM-over-IP Sever Management via SNMP: ‧ Login trial at KVM-over-IP Sever Management failed. Enable SNMP Agent If this option is checked, the KVM-over-IP Sever Management will reply to SNMP requests. Hint: If a community is left blank, you cannot perform the according request. if you want to disable the possibility to reset KVM-over-IP Sever Management via SNMP, do not set a write community. Read Community This is the SNMP community, which allows you to retrieve information via SNMP. Write Community This community allows you to set options and to reset the KVM-over-IP Sever Management or the host via SNMP, i. e. System Location Enter a description of the physical location of the host. The description will be used in reply to the SNMP request "sysLocation. 0". The value will be used in reply to the SNMP request "sysContact. 0". [. . . ] This shifts the processor over and down, guiding it into the board and locking it into place. 140 http://www. TYAN. com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a dealer near you, take the system to them directly to have it serviced instead of attempting to do so yourself (which can have expensive consequences). If these options are not available for you then MiTAC International Corporation can help. [. . . ]