User manual TYAN S8238

[. . . ] S8238 Version 1. 01 Copyright Copyright © 2011 MiTAC International Corporation. No part of this manual may be reproduced or translated without prior written consent from MiTAC International Corporation. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. ® ® Microsoft , Windows are trademarks of Microsoft Corporation. ® Winbond is a trademark of Winbond Electronics Corporation. ® Notice Information contained in this document is furnished by MiTAC International Corporation and has been reviewed for accuracy and reliability prior to printing. [. . . ] Enabled / Disabled 61 http://www. tyan. com 3. 4 PCI/PnP Menu Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Advanced PCI/PnP Settings Clear NVRAM during System Boot. WARING: Setting wrong values in below sections may cause system to malfunction. Clear NVRAM Plug & Play O/S PCI Latency Timer Allocate IRQ to PCI VGA Palette Snooping PCI IDE BusMaster [No] [No] [64] [Yes] [Disabled] [Enabled] ← Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Clear NVRAM Clear NVRAM during system Boot. No / Yes Plug & Play O/S No: lets the BIOS configure all the devices in the system. Yes: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. No / Yes PCI Latency Timer This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. Values in units of PCI clocks for PCI device latency timer register 64 / 32 / 96 / 128 / 160 / 192 / 224 / 248 Allocate IRQ to PCI VGA Yes: assigns IRQ to PCI VGA card if card requests IRQ. Yes / No Palette Snooping This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. Enabled: informs the PCI devices that an ISA graphics device is installed in the system so the card will function correctly. 62 http://www. tyan. com Disabled / Enabled PCI IDE Bus Master Enabled: BIOS uses PCI bus mastering for reading / writing to IDE drives. Enabled / Disabled 63 http://www. tyan. com 3. 5 Boot Menu Main Boot Settings Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Configures settings during System Boot. ←  Boot Settings Configuration  Boot Device Priority  Hard Disk Drives  CD/DVD Drives Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit 3. 5. 1 Boot Settings Configuration Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Boot Settings Configuration Quick Boot Quiet Boot AddOn ROM Display Mode Bootup Num-Lock Wait for ‘F1’ if Error Hit ‘DEL’ Message Display Interrupt 19 Capture Endless Boot [Disabled] [Disabled] [Force BIOS] [On] [Enabled] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. ← Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Quick Boot This option allows user bypass BIOS self test during POST. Enabled / Disabled Quiet Boot Disabled: displays normal POST messages. Disabled / Enabled Add On ROM Display Mode 64 http://www. tyan. com Allows user to force BIOS/Option ROM of add-on cards to be displayed during quiet boot. Force BIOS / Keep Current Boot Up Num-Lock Selects Power-on state for Numlock. On / Off Wait for ‘F1’ If Error Waits for F1 key to be present if error occurs. Enabled / Disabled Hit ‘DEL’ Message Display Displays “Press DEL to run Setup in POST”. Enabled / Disabled Interrupt 19 Capture Enabled: allows option ROMs to trap interrupt 19. Enabled / Disabled Endless Boot Enable/Disable endless loop boot from BBS table. Enabled / Disabled 65 http://www. tyan. com 3. 5. 2 Boot Device Priority Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Boot Device Priority 1st Boot Device 2nd Boot Device [xx, xxx-xxxxx:xxx] [xx, xxx-xxxxx:xxx] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu. [. . . ] Furthermore, if you purchased your system from a dealer near you, take the system to them directly to have it serviced instead of attempting to do so yourself (which can have expensive consequences). If these options are not available for you then TYAN Computer Corporation can help. Besides designing innovative and quality products for over a decade, TYAN ® has continuously offered customers service beyond their expectations. TYAN 's website (www. tyan. com) provides easy-to-access FAQ searches and online Trouble Ticket creation as well as Instant Chat capabilities with our Support Agents. [. . . ]