User manual TYAN S8230

[. . . ] S8230 Version 1. 01 Copyright Copyright © 2010 MiTAC International Corporation. No part of this manual may be reproduced or translated without prior written consent from MiTAC International Corporation. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. ® ® Microsoft , Windows are trademarks of Microsoft Corporation. ® Winbond is a trademark of Winbond Electronics Corporation. ® Notice Information contained in this document is furnished by MiTAC International Corporation and has been reviewed for accuracy and reliability prior to printing. [. . . ] Auto / Disabled 62 http://www. tyan. com 3. 3. 9 Remote Access Configuration Remote Access Enables remote access to system through serial port. Disabled / Enabled NOTE: The following BIOS items are available only when Remove Access is set to [Enabled]. COM1 / COM2 / COM3 (virtual for BMC) Serial Port Mode Select Serial Port settings. None / Hardware / Software 63 http://www. tyan. com Redirection After BIOS POST Disabled: Turns off the redirection after POST Boot Loader. Boot Loader: Redirection is active during POST and during Boot Loader. (Some Oss may not work if set to Always) Always / Disabled / Boot Loader Terminal Type Select the target terminal type. ANSI / VT100 / VT-UTF8 VT-UTF8 Combo Key Support Enable VT-UFT8 Combination Key Support for ANSI/VT100 terminals. Enabled / Disabled Sredir Memory Display Delay Gives the delay in seconds to display memory information. No Delay / Delay 1 Sec / Delay 2 Sec / Delay 4 Sec 64 http://www. tyan. com 3. 3. 10 USB Configuration Legacy USB Support Enables support for legacy USB. Enabled / Disabled / Auto USB 2. 0 Controller Mode Configure the USB 2. 0 controller in Hi Speed (480 Mbps) or Full Speed (12Mbps). Hi Speed / Full Speed BIOS EHCI Hand-OFF This is a work around for OSes without EHCI hand-off support. Enabled / Disabled Legacy USB1. 1 HC Support Enables support for legacy USB. Enabled / Disabled 65 http://www. tyan. com 3. 4 PCI/PnP Menu Clear NVRAM Clear NVRAM during system Boot. No / Yes Plug & Play O/S No: lets the BIOS configure all the devices in the system. Yes: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. No / Yes PCI Latency Timer This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. Values in units of PCI clocks for PCI device latency timer register 64 / 32 / 96 / 128 / 160 / 192 / 224 / 248 Allocate IRQ to PCI VGA Yes: assigns IRQ to PCI VGA card if card requests IRQ. 66 http://www. tyan. com Yes / No Palette Snooping This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. Enabled: informs the PCI devices that an ISA graphics device is installed in the system so the card will function correctly. Disabled / Enabled PCI IDE Bus Master Enabled: BIOS uses PCI bus mastering for reading / writing to IDE drives. Enabled / Disabled Offboard PCI/ISA IDE Card Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. [. . . ] Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a dealer near you, take the system to them directly to have it serviced instead of attempting to do so yourself (which can have expensive consequences). If these options are not available for you then TYAN Computer Corporation can help. Besides designing innovative and quality products for over a decade, TYAN ® has continuously offered customers service beyond their expectations. [. . . ]