User manual TYAN S8228

[. . . ] S8228 Version 1. 00 Copyright Copyright © MiTAC Computer Corporation, 2011. No part of this manual may be reproduced or translated without prior written consent from MiTAC Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN is a trademark of MiTAC Computer Corporation ® ® AMD , Opteron , and combinations thereof are trademarks of AMD Corporation. ® ® AMI , AMIBIOS and combinations thereof are trademarks of AMI Technologies. [. . . ] Gives the delay in seconds to display memory information. Sredir Memory Display Delay 54 http://www. TYAN. com 3. 7. 8 - USB Configuration Sub- Menu You can use this screen to view the USB Configuration Menu. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. Feature USB Configuration Legacy USB Support Option Disabled Enabled AUTO Description Enables support for legacy USB. AUTO option disables legacy support if no USB devices are connected. Configure the USB 2. 0 controller in Hi Speed (480Mbps) or Full Speed (12Mbps). Support USB1. 1 HC USB 2. 0 Controller Mode Hi Speed Full Speed Enabled BIOS EHCI Hand-Off Disabled Legacy USB1. 1 HC Support Disabled Enabled AUTO Disabled 1 port 2 port 4port 6ports USB port Enable1//2/4/6 Ports in OS 55 http://www. TYAN. com 3. 7. 9 - Hyper Transport Configuration Sub-Menu You can use this screen to view the Hyper Transport Configuration Menu. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. 56 http://www. TYAN. com 3. 7. 9. 1 – NonCoherent HT Configuration Sub-Menu Feature Option NonCoherent HT Configuration Auto 200~800Hz 1. 2GHz 1. 4GHz 1. 6GHz 1. 8GHz 2. 0GHz 2. 2GHz 2. 4GHz 2. 6GHz Auto 4bit/8bit/16bit Description Non-Coherent HT Link Speed The HyperTransport link will run at this speed if it is slower than or equal to the system clock and the board is capable. Non-Coherent HT Link Width The HyperTransport link will run at this Width. 57 http://www. TYAN. com 3. 8 - Boot Menu You can display Boot Setup option by highlighting it using the Arrow (/) keys and pressing Enter. The settings are described on the following pages. 58 http://www. TYAN. com 3. 8. 1 - Boot Settings Configuration Sub-Menu Use this screen to select options for the Boot Settings Configuration. Use the Plus and Minus (+/-) keys to change the value of the selected option. Feature Boot Settings Configuration Quick Boot Option Enabled Disabled Disabled Description This option allows user bypass BIOS self test during POST. Displays “Press DEL to run Setup” in POST. Quiet Boot Enabled Wait for ‘F1’ If Error Hit ‘DEL’ Message Display Enabled Disabled Enabled Disabled 59 http://www. TYAN. com 3. 8. 2 - Boot Device Priority Use this screen to select options for the Boot Device Priority. Use the Plus and Minus (+/-) keys to change the value of the selected option. Feature Option Boot Device Priority Network: IBA GE Slot 0200 v1335 1st Boot Device Disabled Description Specifies the boot sequence from the available devices. 60 http://www. TYAN. com 3. 8. 3 - Network Drives Use this screen to select options for the Network Drives. Use the Plus and Minus (+/-) keys to change the value of the selected option. Feature Option Network Drives 1st Drive Network: IBA GE Slot 0200 v1335 Network: IBA GE Slot 0300 v1335 Network: IBA GE Slot 0301 v1335 Disabled Network: IBA GE Slot 0200 v1335 Network: IBA GE Slot 0300 v1335 Network: IBA GE Slot 0301 v1335 Disabled Network: IBA GE Slot 0200 v1335 Network: IBA GE Slot 0300 v1335 Network: IBA GE Slot 0301 v1335 Disabled Description Specifies the boot sequence from the available devices. 2nd Drive Specifies the boot sequence from the available devices. Specifies the boot sequence from the available devices. 3nd Drive 61 http://www. TYAN. com 3. 9 - Security Menu The system can be configured so that all users must enter a password every time the system boots or when BIOS Setup is entered, using either the Supervisor password or User password. The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password. If you forget it, you must clear CMOS and reconfigure. Feature Security Settings Supervisor Password: Option Description If the password has been set, Installed displays. Selects this option to change or install User Password. Not Installed Installed Not Installed User Password: Installed Change Supervisor Password Change User Password [Enter] [Enter] 62 http://www. TYAN. com 3. 10 - Chipset Menu This menu allows the user to customize functions of the AMD Chipsets. Select a menu by highlighting it using the Arrow (/) keys and pressing Enter. The settings are described on the following pages. 63 http://www. TYAN. com 3. 10. 1 – NorthBridge Chipset Configuration Sub- Menu This menu gives options for Northbridge Chipset settings. Select a menu by highlighting it using the Arrow (/) keys and pressing Enter. The settings are described on the following pages. 64 http://www. TYAN. com 3. 10. 1. 1 – Memory Configuration Sub- Menu Feature Memory Configuration Option Description Bank Interleave setting has to do with the actual RAM chip properties, most good quality RAM chips have "4-bank interleaving" and work best at this setting. Enable Bank Memory Interleaving Enable Node Memory Interleaving Enable Channel Memory Interleaving Reserve a spare memory rank in each mode Enable or disable bank swizzle mode Auto Bank Interleaving Disabled Node Interleaving Channel Interleaving CS Sparing Enable Bank Swizzle Mode Auto Disabled Auto Disabled Disabled Enabled Disabled Enabled 65 http://www. TYAN. com 3. 10. 1. 2 - ECC Configuration Sub-Menu Feature ECC Chipset Configuration Option Disabled Basic Good Super Max user Enabled Enabled 1. 31ms Disabled Disabled Disabled Description ECC Mode Set the level of ECC protection. [. . . ] This shifts the processor over and down, guiding it into the board and locking it into place. 90 http://www. TYAN. com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a dealer near you, take the system to them directly to have it serviced instead of attempting to do so yourself (which can have expensive consequences). If these options are not available for you then TYAN Computer Corporation can help. [. . . ]