User manual TYAN S8212

[. . . ] S8212 Version 1. 01 Copyright Copyright © 2009 MiTAC International Corporation. No part of this manual may be reproduced or translated without prior written consent from MiTAC International Corporation. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. ® ® Microsoft , Windows are trademarks of Microsoft Corporation. ® Winbond is a trademark of Winbond Electronics Corporation. ® Notice Information contained in this document is furnished by MiTAC International Corporation and has been reviewed for accuracy and reliability prior to printing. [. . . ] Enabled / Disabled AMI OEMB Table Set this value to allow the ACPI BIOS to add a pointer to an OEMB table in the Root System Description Table (RSDT) table. Enabled / Disabled NOTE: OEMB table is used to pass POST data to the AMI code during ACPI O/S operations. Disabled / Enabled 49 http://www. tyan. com 3. 3. 6 Advanced Hardware Health Configuration Smart FAN configuration Select SmartFan mode: Disable; Thermal Cruise: Fan steady in tartget Temp range. Sensor Data Register Monitoring Sensor Monitoring for BMC. 50 http://www. tyan. com 3. 3. 6. 1 Sensor Data Register Monitoring Sensor Monitoring for BMC. Read only. It can not be modified in user mode. 51 http://www. tyan. com 3. 3. 7 IPMI 2. 0 Configuration View BMC System Event Log View all events in the BMC Event Log. (Parameter #1 to 4) BMC Watch Dog Timer Action Allows the BMC to reset or power down the system if the operating system crashes or hangs. Disabled / Enable BMC Alert LED and Beep BMC Alert LED and Beep ON / OFF FW Key Enter IPMI FW Key upgrade to IPMI or iKVM function. [0000000] 52 http://www. tyan. com 3. 3. 7. 1 View BMC System Event Log 3. 3. 7. 2 Set PEF Configuration Parameters Command Enable or Disable PEF Support. 53 http://www. tyan. com 3. 3. 8 MPS Configuration Configure the Multi-Processor Table. Select MPS Revision [1. 1] / [1. 4] 54 http://www. tyan. com 3. 3. 9 PCI-Express Configuration Enable or Disable PCI Express L0 and L1 link power states. 55 http://www. tyan. com 3. 3. 10 Remote Access Configuration Remote Access Enables remote access to system through serial port. Disabled / Enabled Serial port number Select Serial Port for console redirection. COM1/ COM2 / COM3 (virtual for BMC) Serial Port Mode Select Serial Port settings. None / Hardware / Software Redirection After BIOS POST Disabled: Turns off the redirection after POST Boot Loader; Boot Loader: Redirection is active during POST and during Boot Loader; Always: Redirection is always active. (Some OSs may not work if set to Always) Terminal Type 56 http://www. tyan. com Select the target terminal type. ANSI / VT100 / VT-UTF8 VT-UTF8 Combo Key Support Enable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. Disabled / Enable Sredir Memory Display Delay Gives the delay in seconds to display memory information. No Delay / Delay 1 Sec / Delay 2 Sec / Delay 4 Sec 57 http://www. tyan. com 3. 3. 11 USB Configuration Legacy USB Support Enables support for legacy USB. Disabled / Enabled / Auto USB 2. 0 Controller Mode Configure the USB 2. 0 controller in Hi Speed (480 Mbps) or Full Speed (12Mbps). Hi Speed / Full Speed BIOS EHCI Hand-OFF This is a work around for OSes without EHCI hand-off support. Enabled / Disabled Legacy USB1. 1 HC Support Enables support for legacy USB. Enabled / Disabled USB Mass Storage Device Configuration Configure the USB Mass Storage Class Devices. 58 http://www. tyan. com 3. 4 PCI/PnP Menu Clear NVRAM Clears NVRAM during system Boot. No / Yes Plug & Play O/S No: lets the BIOS configure all the devices in the system. Yes: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. No / Yes PCI Latency Timer This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. [. . . ] The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. 83 http://www. tyan. com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a dealer near you, take the system to them directly to have it serviced instead of attempting to do so yourself (which can have expensive consequences). [. . . ]