User manual TYAN S5502-S5502WGM3NR

[. . . ] MiTAC retains the right to make changes to product descriptions and/or specifications at any time, without notice. In no event will MiTAC be held liable for any direct or indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting from errors or inaccuracies of information contained in this document. 1 http://www. tyan. com About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: Chapter1: Instruction This chapter describes the features of the motherboard and the new technology it supports. Chapter2: Board Installation This chapter lists the hardware setup procedures that you need to abide by when installing system components. It includes description of the jumpers and connectors on the motherboard. [. . . ] Enabled / Disabled Package C state undemotion Enable Package C state undemotion. Disabled / Enabled C State Pre-Wake Enable or Disable C State Pre-Wake feature. Enabled / Disabled Package C State Limit Select Package C State Limit. Auto / C0/C1 / C2 / C3 / C6/ C7 / C7s Intel TXT(LT) Support Enable/Disable Intel® TXT(LT) support. Disabled / Enabled 62 http://www. tyan. com 3. 3. 5 SATA Configuration SATA Mode Selection Determines how SATA controller(s) operate. IDE / AHCI / RAID Aggressive LPM Support Enable PCH to aggressively enter link power state. Enabled / Disabled SATA Controller Speed Indicates the maximum speed the SATA controller can support. Default / Gen1 / Gen2 / Gen3 Serial ATA Port 0/1/2/3/4/5 /Software Preserve Read only. Enabled / Disabled 63 http://www. tyan. com Hot Plug Designates this port as Hot Pluggable. Enabled / Disabled Mechanical Presence Switch Controls reporting if this port has a Mechanical Presence Switch. Disabled / Enabled Spin Up Device On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device. VT-UTF8 / VT100 / VT100+ / ANSI Bits per Second Select serial port transmission speed. 38400 / 9600 / 19200 / 115200 / 57600 Data Bits 8/7 Parity A parity bit can be sent with the data bits to detect some transmission errors. Even: parity bit is 0 if the num of 1’s in the data bits is even. None / Even / Odd / Mark / Space 74 http://www. tyan. com Stop Bits Stop bits indicate the end of a serial data packet. 1/2 Flow Control Flow Control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a ‘stop’ signal can be sent to stop the data flow. Once the buffers are empty, a ‘start’ signal can be sent to restart the flow. None / Hardware RTS/CTS VT-UTF8 Combo Key Support Enable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. Enabled / Disabled Recorder Mode With this mode enabled only text will be sent. Disabled / Enabled Resolution 100x31 Enable or disable extended terminal resolution. Disabled / Enabled Legacy OS Redirection Resolution On Legacy OS, the number of rows and columns supported redirection. [. . . ] ZCR (Zero Channel RAID): PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. 112 http://www. tyan. com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. [. . . ]