User manual TRIMBLE TERRASYNC 2.52 RELEASE NOTES REV A

[. . . ] TerraSyncTM software Release Notes Introduction New Features and Changes Product Information Registering the TerraSync Software Installation on a CE Device Installation on a PC Cabling Known Issues Technical Assistance Version 2. 52 Part Number 43161-26-ENG Revision A October 2005 Contact Information Trimble Navigation Limited Mapping & GIS Division 7401 Church Ranch Blvd Westminster, CO 80021 USA www. trimble. com Copyright and Trademarks © 2000­2005, Trimble Navigation Limited. For STL support, the TerraSync software uses the Moscow Center for SPARC Technology adaptation of the SGI Standard Template Library. © 1994 Hewlett-Packard Company, © 1996, 97 Silicon Graphics Computer Systems, Inc. , © 1997 Moscow Center for SPARC Technology. Portions of this computer program are copyright © 1995-1999 LizardTech, Inc. [. . . ] If you are upgrading or reinstalling the TerraSync software, make sure you disconnect from GPS and exit the software. If there is no partnership, or the computers do not connect, you may need to reinstall the ActiveSync technology on the office computer. For more information, refer to the documentation for the CE device. B B Tip ­ If the ActiveSync technology is installed, but the two computers do not connect, check that the CE device is set up to establish a PC connection. For information on how to do this, refer to the documentation for the CE device. Tip ­ Ensure that the CE device is configured to connect at the maximum baud rate available. When the two computers are connected, the Microsoft ActiveSync window appears. 5. Make sure that the TerraSync software is not running on the CE device. Insert the TerraSync Software CD in the CD drive of the office computer. TerraSync Software Release Notes 19 6. If this screen does not appear, run setup. exe from the CD drive folder. Follow the instructions on the screen to install the TerraSync software. You will need to enter your installation serial number, which you can obtain by registering your copy of the software. For more information, see Registering the TerraSync Software, page 16. If the CE device has a non-volatile "internal" secondary storage location, this is used as the default installation location. Internal secondary storage locations include the Disk on a GeoExplorer series handheld and the Built-In Storage on a Trimble Recon handheld. 20 TerraSync Software Release Notes If the device has no secondary storage, or only has removable secondary storage such as a CompactFlash card, the default installation location is the main memory (RAM). Note ­ If an SD (Secure Digital) memory card is inserted in the handheld, the card appears as an installation location option. Trimble recommends that you install software to the handheld's flash disk, not to an SD memory card. If you install software to a card and then remove the card from the handheld, the software will not be available for use. Respond to any messages that appear: ­ If a message appears on the CE device stating that the TerraSync software is already installed, and asking if you want to reinstall the TerraSync software, tap Yes. If the message Confirm ignore missing file appears on the CE device, tap Yes to All. If the message Install "Trimble TerraSync" to \Disk\Trimble TerraSync\ ?If the message The program you have installed may not display properly because it was designed for a previous version of Windows Mobile software. appears on the CE device, tap OK. ­ ­ ­ This warning appears on devices running Windows Mobile 2003 Second Edition or later when you install software that is designed to support previous versions of Windows CE. Note ­ On some CE devices, such as the Trimble Recon handheld, the message Adding information for "Remove Programs" may remain on the screen for several minutes. [. . . ] To turn off the receiver, use the Power button p on the receiver. · 12. 8 GeoExplorer series handheld · If a GeoExplorer series handheld loses power, or you perform a hard reset, the main memory is cleared. Any unsaved data and any changes in the main memory since the last backup are lost. When you install the TerraSync software on a GeoExplorer series handheld, some settings are stored in the main memory, even though the TerraSync software is always installed to the Disk. To protect these settings, the TerraSync software installation program automatically backs up the main memory after installing the TerraSync software. [. . . ]