User manual TRIMBLE TERRASYNC 1.22 RELEASE NOTES REV A

[. . . ] TerraSyncTM Release Notes Version 1. 22 October 2001 Revision A Trimble Navigation Limited Mapping & GIS Division 645 North Mary Avenue Post Office Box 3642 Sunnyvale, CA 94088-3642 U. S. A. Phone: +1-408-481-8940 1-800-545-7762 Fax: +1-408-481-7744 www. trimble. com Legal Information Revision Notice This is the October 2001 release (Revision A) of the TerraSync Release Notes. It applies to version 1. 22 of the TerraSyncTM software. Copyright © 2000­2001 Trimble Navigation Limited. For STL support, the TerraSync software uses the Moscow Center for SPARC Technology adaptation of the SGI Standard Template Library. © 1994 Hewlett-Packard Company, © 1996, 97 Silicon Graphics Computer Systems, Inc. , © 1997 Moscow Center for SPARC Technology. Trademarks The Globe & Triangle logo, Trimble, BoB, TerraSync, and Trimble Survey Controller are trademarks of Trimble Navigation Limited. [. . . ] The TerraSync software requires at least 8 MB of free RAM to install and 10 MB of free Disk storage (if applicable). NOTE Trimble recommends that you uninstall any previously installed versions of the TerraSync software before installing the latest version. If memory space is insufficient, the following message appears during installation: Click Cancel, remove any unwanted programs or data files from your CE device, and/or increase storage memory (see Changing Memory Allocation). More. . . TerraSync Release Notes Installation 20 To install the TerraSync software: 1. Connect the CE device to the office computer, using one of the following: · · · · · Serial cable Cradle Infrared Modem Network card For information on connecting your CE device to another computer, refer to the documentation for your CE device. If an ActiveSync partnership for these two computers exists, ActiveSync should start and the office computer should connect to the CE device automatically. If there is no partnership, or the computers do not connect, you may need to install or set up ActiveSync on your office computer. For more information, refer to the documentation for your CE device. More. . . TerraSync Release Notes Installation 21 When the two computers are connected, the Microsoft ActiveSync window appears and displays the message Connected: TIP TIP If ActiveSync is installed, but the two computers do not connect, check that the CE device is set up to establish a PC connection. You should also ensure that the CE device is configured to connect at the maximum baud rate available. 3. Download the appropriate TerraSync upgrade package from the TerraSync download page on the Trimble website. The package that you need depends on the platform, operating system version, and processor type of your CE device. The TerraSync installation wizard appears: More. . . TerraSync Release Notes Installation 23 5. Follow the instructions on the screen to install the TerraSync software. Enter either your TerraSync version 1. 22 serial number and installation key (displayed on the CD case), or your upgrade code. When the message Install "Trimble TerraSync" using the default application install directory?appears, do one of the following: · · Click Yes to install the software to the default location. Use this option unless your device has a secondary internal storage location. Click No to install the software to a secondary internal storage location, such as the TDS Ranger's Disk. From the Save In list, select Disk (or C_Drive), then click OK to proceed with the installation. Use this option when installing onto a TDS Ranger. TIP Trimble recommends that you install to a secondary storage location to free up internal storage and program memory on the CE device. Do not install the TerraSync software to a removable storage location such as a CompactFlash card. WARNING TerraSync Release Notes Installation 24 Incomplete Installation If you install the software to a secondary internal storage location, such as the TDS Ranger's Disk, the TerraSync installation program copies an installation file to a temporary location on the device, then "unpacks" it to the Disk. Occasionally there is enough space to copy the installation file to the device, but not enough space to unpack it to the Disk. [. . . ] More. . . TerraSync Release Notes Manual Additions 44 In the TerraSync software, you can set either a PDOP mask or an HDOP mask. In the GPS Settings form in the Setup section, you can configure settings either in Custom mode or in Slider mode: · · In Slider mode, adjust the slider position to select one of nine pre-defined PDOP mask values. In Custom mode, from the DOP Type field select PDOP or HDOP, and then in the DOP Mask field specify a precise value. Any status information relating to DOP values indicates the selected DOP type. For example, when HDOP is selected and the HDOP value exceeds the mask, the message Poor satellite geometry (HDOP) appears in the Skyplot, Satellite information, and Receiver Status screens, and appears as a ToolTip for the flashing satellite icon. [. . . ]