User manual TP-LINK TL-WR1043ND

[. . . ] TL-WR1043ND 300Mbps Wireless N Gigabit Router Rev: 2. 3. 0 1910010817 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. http://www. tp-link. com is a registered trademark of TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] Assigned IP - The IP address that the router has allocated to the DHCP client. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. -45- TL-WR1043ND 300Mbps Wireless N Gigabit Router You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 4. 7. 3 Address Reservation Choose menu “DHCP→Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 4-29). When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 4-29 Address Reservation MAC Address - The MAC address of the PC for which you want to reserve IP address. (Pop-up Figure 4-30) Enter the MAC address (in XX-XX-XX-XX-XX-XX format) and IP address of the computer you wish to add in dotted-decimal notation. Click the Save button when finished. Figure 4-30 Add or Modify an Address Reservation Entry -46- TL-WR1043ND To modify or delete an existing entry: 1. 3. 300Mbps Wireless N Gigabit Router Click the Modify in the entry you want to modify. Click the Save button. Click the Enable/ Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return to the previous page. 4. 8 USB Settings Figure 4-31 The USB Settings menu There are five submenus under the USB Settings menu (shown in Figure 4-31): Storage Sharing, FTP Server, Media Server, Print Server and User Accounts. Click any of them, and you will be able to configure the corresponding function. 4. 8. 1 Storage Sharing Choose menu “USB Settings→Storage Sharing”, and then you can configure a USB disk drive attached to the router on this page as shown in Figure 4-32. Figure 4-32 Storage Sharing -47- TL-WR1043ND 300Mbps Wireless N Gigabit Router Service Status - Indicates the Storage Sharing service's current status, started or stopped. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it. When the volume is shared, you can click the Disable to stop sharing the volume; when volume is non-shared, you can click the Enable button to share the volume. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. A message (as shown in Figure 4-33) will appear on your web browser when it is safe to detach the USB disk. Figure 4-33 Safe Unplug Message Click the Rescan button to start a new scan. Follow the instructions below to set up your router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this router. Click the Rescan button to find the USB drive that has been attached to the router. The screen will appear as shown in Figure 4-34. Figure 4-34 Storage Sharing -48- TL-WR1043ND 3. 6. 300Mbps Wireless N Gigabit Router Click the Start button to start the Storage Sharing service. It is not recommended to simply pull the USB drive out of the USB port, because this can cause damage to the device and cause data loss. 4. Mounted volumes are subject to the 8-volume limit, so you cannot access more than 8 volumes on the USB storage device. 4. 8. 2 FTP Server Choose menu “USB Settings→FTP Server”, and then you can configure FTP Server on this page as shown in Figure 4-35. Figure 4-35 FTP Server Configuration Server Status - Indicates the FTP Server’s current status, started or stopped. You can click the Start button to start the FTP Server and click the Stop button to stop it. Internet Access – Indicates the current status of Internet Access. [. . . ] Install TCP/IP component 1) On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. 2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window. 3) Right click the icon that showed below, select Properties on the prompt page. Figure B-1 4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP). Figure B-2 -109- TL-WR1043ND 5) 300Mbps Wireless N Gigabit Router The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 6) Select Obtain an IP address automatically and Obtain DNS server automatically, as shown in the Figure below: Figure B-3 -110- TL-WR1043ND 300Mbps Wireless N Gigabit Router Appendix C: Specifications General Standards Protocols Ports IEEE 802. 3, IEEE 802. 3u, IEEE 802. 11b, IEEE 802. 11g and IEEE 802. 11n TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP One 10/100/1000M Auto-Negotiation WAN RJ45 port, Four 10/100/1000M Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) Cabling Type 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 1000BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) LEDs Safety & Emissions Wireless Frequency Band* Radio Data Rate Frequency Expansion Modulation Security 2. 4~2. 4835GHz 11n：up to 300Mbps (Automatic) 11g：54/48/36/24/18/12/9/6M (Automatic) 11b：11/5. 5/2/1M (Automatic) DSSS (Direct Sequence Spread Spectrum) DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM WEP/WPA/WPA2/WPA2-PSK/WPA-PSK 270M: -68dBm@10% PER; 130M: -68dBm@10% PER 108M: -68dBm@10% PER; 54M: -68dBm@10% PER 11M: -85dBm@8% PER; 6M: -88dBm@10% PER; 1M: -90dBm@8% PER 5dBi * 3 Power, System, WLAN, WAN, LAN (1-4), WPS, USB FCC, CE Sensitivity @PER Antenna Gain Environmental and Physical Temperature. Humidity Operating : 0℃~40℃ (32℃~104℃) Storage: -40℃~70℃ (-40℃~158℃) Operating: 10% - 90% RH, Non-condensing Storage: 5% - 90% RH, Non-condensing * Only 2. 412GHz~2. 462GHz is allowed to be used in USA, which means only channel 1~11 is available for American users to choose. [. . . ]