User manual TP-LINK TL-WPA4220

[. . . ] TL-WPA4220 300Mbps AV500 WiFi Powerline Extender TL-WPA2220 300Mbps AV200 WiFi Powerline Extender REV1. 0. 0 1910010839 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] The detailed explanations for each submenu are provided below. Figure 3-8 Wireless menu 3. 4. 1 Wireless Settings Selecting Wireless > Wireless Settings will enable you to configure the basic settings for your wireless network on the screen below (Figure 3-9). Figure 3-9 Wireless Settings SSID (Set Service Identifier) - Identifies your wireless network name. The same Name (SSID) must be assigned to all wireless devices in your network. The default SSID is TP-LINK_XXXXXX (XXXXXX indicates the last six unique characters of each device’s MAC address). This field specifies the region where the wireless function of the powerline extender can be used. It may be illegal to use the wireless 15 TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender function of the powerline extender in a region other than one of those specified in this filed. If your country or region is not listed, please contact your local government agency for assistance. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog Channel - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. If you select Auto, then the powerline extender will choose the best channel automatically. The options are: • • • • • 11b only - Only 802. 11b wireless stations can connect to the device. 11bg mixed - Both 802. 11b and 802. 11g wireless stations can connect to the device. 11bgn mixed - All 802. 11b, 802. 11g and 802. 11n wireless stations can connect to the device. If all of the wireless devices connected with the powerline extender can connect in the same transmission mode (e. g. If you have some devices that use different transmission modes, choose the appropriate Mixed mode. Enable Wireless Powerline Extender Radio - The wireless radio of the powerline extender can be enabled or disabled to allow or deny wireless stations to access. If it is enabled, the wireless stations will be able to access the powerline extender; otherwise, wireless stations will not be able to access the powerline extender. Enable SSID Broadcast - Selecting this check box will allow the device to broadcast its name (SSID) on the air. If it’s allowed, when wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the device. Note: To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 3. 4. 2 Wireless Security Selecting Wireless > Wireless Security will enable you to configure wireless security for your wireless network to protect your data from intruders. The powerline extender provides three security types: WEP, 16 TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender WPA/WPA2 and WPA-PSK/WPA2-PSK. The default password can be found on the label at the bottom of the device. [. . . ] Press and hold the Pair button on powerline device C TL-PA4010 for one second. 37 TL-WPA4220/TL-WPA2220 Step 2. Step 3. 300Mbps AV500/AV200 WiFi Powerline Extender Within two minutes, press and hold the Pair button on Powerline device A/B for one second. Wait for about 60 seconds while your powerline devices are connecting. The Power LED on powerline device A/B and C will stop flashing and become solid light when the connection is made. Note: The sequence of Step 1 and Step 2 can be exchanged. [. . . ]