User manual TP-LINK TL-WN751ND

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. [. . . ] Channel - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. The options are: · 54Mbps (802. 11g) - Both 802. 11g and 802. 11b wireless stations can connect to the router. · 11Mbps (802. 11b) - Only 802. 11b wireless stations can connect to the router. Note: The default is "54Mbps (802. 11g)", which allows both 802. 11g and 802. 11b wireless stations to connect to the router. Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the Wireless Router SSID will broadcast its name (SSID) on the air. Enable Wireless Security ­ The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the router without encryption. It is recommended strongly that you choose this option to encrypt your wireless network. Authentication Type - You can select one of the following authentication types: · WEP - Select WEP authentication type based on 802. 11 authentications. · WPA-PSK/WPA2-PSK - Select WPA/WPA2 authentication type based on pre-shared passphrase. · WPA /WPA2 - Select WPA/WPA2 authentication type based on Radius Server. Authentication Options - You can select one of the following authentication options: · When you select WEP for authentication type you can select the following authentication options: · Automatic - Select Shared Key or Open System authentication type automatically 30 TL-WN751ND based on the wireless station request. · · · · 54Mbps Wireless Router User Guide Shared Key - Select 802. 11 Shared Key authentication. Privilege - Select the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit / 152-bit. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field, enter any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. Status - Select Enabled or Disabled for this entry on the Status pull-down list. Note: When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be enabled. Click the Save button. Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries 33 TL-WN751ND previous page. 54Mbps Wireless Router User Guide Click the Next button to go to the next page and click the Previous button to return to the For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE be able to access the router. The wireless station B with MAC address 00-0A-EB- 00-07-5F not be able to access the router, and the wireless station C with MAC address 00-0A-EB-00-07-8A be able to access the router when its WEP key is 2F34D20BE2E 54B326C5476586A, while all other wireless stations cannot access the router, you should configure the Wireless MAC Address Filtering list by following these steps: 1. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. button and enter the MAC address 00-0A-EB-00-07-BE in the MAC Address field, enter wireless station A in the Description field, select Allow in the Privilege pull-down list and select Enabled in the Status pull-down list. button and enter the MAC address 00-0A-EB-00-07-5F in the MAC Address field, enter wireless station B in the Description field, select Deny in the Privilege pull-down list and select Enabled in the Status pull-down list. button and enter the MAC address 00-0A-EB-00-07-8A in the MAC Address field, enter wireless station C in the Description field, select 128-bit in the Privilege pull-down list, enter 2F34D20BE2E54B326C5476586A in the WEP Key field and select Enabled in the Status pull-down list. [. . . ] First make sure your Ethernet Adapter is working, refer to the adapter's manual if needed. Install TCP/IP component 1) 2) 3) On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window. Right click the icon that showed below, select Properties on the prompt page. Figure 1 4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP). Figure 2 67 TL-WN751ND 5) this window by default. 54Mbps Wireless Router User Guide The following TCP/IP Properties window will display and the IP Address tab is open on Now you have two ways to configure the TCP/IP protocol below: Setting IP address automatically Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below: Figure 3 Setting IP address manually 1 2 3 4 Select Use the following IP address radio button. [. . . ]