User manual TP-LINK TL-WN723N

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Limited by local law regulations, version for North America does not have region selection option. Channel - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. The options are: · · · · 108Mbps (Dynamic) - Super GTM, 802. 11g and 802. 11b wireless stations can connect to the router. 108Mbps (Static) - Only Super GTM wireless stations can connect to the router. 54Mbps (802. 11g) - Both 802. 11g and 802. 11b wireless stations can connect to the router. 11Mbps (802. 11b) - Only 802. 11b wireless stations can connect to the router. Note: The default is "54Mbps (802. 11g)", which allows both 802. 11g and 802. 11b wireless stations to connect to the router. Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the Wireless Router SSID will broadcast its name (SSID) on the air. Enable Wireless Security ­ The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the router without encryption. To set up an entry, follow these instructions: First, you must decide whether the unspecified wireless stations can access the router or not. If you desire that the unspecified wireless stations can access the router, please select the radio button Allow the stations not specified by any enabled entries in the list to access, otherwise, select the radio button Deny the stations not specified by any enabled entries in the list to access. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 5-20: Figure 5-20 To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter a simple description of the wireless station in the Description field. Privilege - Select the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit / 152-bit. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field, enter any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. Status - Select Enabled or Disabled for this entry on the Status pull-down list. Click the Save button to save this entry. To add additional entries, repeat steps 1-6. - 33 - TL-WN723N Note: 108M Wireless Router User Guide When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be enabled. Click the Save button. Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE be able to access the router. [. . . ] And the following items available If the router's LAN IP address is 192. 168. 1. 1, type IP address is 192. 168. 1. x (x is from 2 to 254), and Subnet mask is 255. 255. 255. 0. Type the router's LAN IP address (the default IP is 192. 168. 1. 1) into the Default gateway field. In the Preferred DNS Server field you can type the DNS server IP address, which has been provided by your ISP - 71 - TL-WN723N 108M Wireless Router User Guide Figure 4 - 72 - TL-WN723N 108M Wireless Router User Guide Appendix C: Specifications General Standards Protocols Ports Cabling Type IEEE 802. 3, 802. 3u, 802. 11b and 802. 11g TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) Radio Data Rate LEDs Safety & Emissions 108/54/48/36/24/18/12/9/6Mbps or 11/5. 5/3/2/1Mbps PWR, SYS, WLAN, WAN, 1, 2, 3, 4 FCC, CE Environmental and Physical Operating Temp. Operating Humidity 0~40 (32~104) 10% - 90% RH, Non-condensing - 73 - TL-WN723N 108M Wireless Router User Guide Appendix D: Glossary 108M Super GTM WLAN Transmission Technology - 108M Super GTM WLAN Transmission Technology employs multiple performance-enhancing techniques including packet bursting, fast frames, data compression, and dynamic turbo mode that combine to improve the throughput and range of wireless networking products. [. . . ]