User manual TENDA W54P-W54P+

[. . . ] Without the permission of Shenzhen Tenda Technology Co. , Ltd, any individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages. All the photos and product specifications mentioned in this guide are for references only. [. . . ] There is no security threat to your computer. -8- W54P/W54P+ User Guide 8. Click “Finish” to complete the installation. -9- W54P/W54P+ User Guide Chapter 3 Client Utility Interface The included client utility is for the W54P/W54P+ Wireless PCI Adapter management. If it does not appear, select “Start”—“All Programs” —“TENDA” —“ W54P/W54P+”, or click the shortcut on your PC’s desktop. Note: In the Windows XP, you can select the included W54P/W54P+ Windows XP Client internal Utility Interface or the to wireless application configure the device. There are two client utility applications in W54P/ W54P+: Station Mode and AP Mode. Note: In this utility interface, Station Mode (Client Mode) is the default access way. -10- W54P/W54P+ User Guide 3. 1 3. 1. 1 Station Mode Station Mode Topology In this mode, W54P/W54P+ serves as a client to receive the wireless signals to access the Internet. -11- W54P/W54P+ User Guide 3. 1. 2 Status In the Network Status window, it displays something on wireless adapter and wireless network’s status, including SSID, Authentication type, Encryption Type, IP address, subnet mask and gateway and so on. -12- W54P/W54P+ User Guide 3. 1. 3 Site Survey The Site Survey is used to scan the available wireless network around, showing the wireless network’s signal strength and other information which provides basis for you to access which wireless network. Connect: select one entry in the wireless network list and click the button to connect the device with the selected network. Refresh: rescan the wireless network around. -13- W54P/W54P+ User Guide 3. 1. 4 Profile Management This window saves the general wireless parameters for different profiles, which is used to fast connect the wireless network you need. UP/DOWN: To change the profile’s sequence in the list. New: To create a new profile and configure the site status and security setting. Delete: To delete one existing profile. -14- W54P/W54P+ User Guide (Site Status) (Security Setting) -15- W54P/W54P+ User Guide 3. 1. 5 Statistics Statistics is used to summarize Rx and Tx data packets, including the success and error packet amount. Clear: click this button to renew the statistics. 3. 1. 6 WPS Setting WPS setting is enabled only on WPS-compliant devices. -16- W54P/W54P+ User Guide PIN： Enter the Pin code and click the “PIN” to automatically connect the wireless adapter with wireless devices around. PBC： Click the “PBC” to complete auto-check and connections between wireless adapter and other wireless device. Disconnect: to disconnect the connected wireless network. -17- W54P/W54P+ User Guide 3. 2 3. 2. 1 AP Mode AP Mode Topology The device also can serve as an access point to transmit wireless signals and create wireless network, allowing other wireless clients to access the network. Click the AP Mode icon to enter the AP Mode interface. -18- W54P/W54P+ User Guide 3. 2. 2 Basic Setting This window is used to configure the AP’s basic parameters, including SSID, Wireless Mode and Channel. SSID: Wireless network’s ID name scanned by wireless adapter. Restore Default: to restore the set parameters to default factory default settings. Apply: to make the changes take effect. -19- W54P/W54P+ User Guide 3. 2. 3 Security Setting This window is used to configure the wireless network’s security authentication, providing WEP, WPA-PSK, WPA2-PSK, and WPA-PSK/WPA2-PSK encryption methods. WEP：10/26 bits Hex or 5/13 ASCII support. [. . . ] Ad-Hoc A group of computers each with wireless adapters, connected as an independent WLAN. AES Advanced Encryption Standard -24- W54P/W54P+ User Guide BSSID DHCP DSSS Basic Service Set ID Dynamic Host Configuration Protocol Direct Sequence radio. [. . . ]