User manual TANGENT CDP-200

[. . . ] Power cords Wiring must be organised to prevent people from stepping on the cables and to avoid pinching by objects placed on or beside them. Take special care around sockets and plug boxes and where the power cords leave the unit. Ventilation The cabinet is provided with slots and openings to ensure ventilation and reliable operation and to protect the unit against overheating. The openings must never be blocked, for instance by placing the unit on a bed, a sofa, a carpet or similar surface. Overloading Make sure that wall sockets, extension cords and plug boxes are not overloaded as this may lead to fire or electrical shock. 05 IMPORTANT SAFETY INSTRUCTIONS Lightning Unplug the unit for additional protection during thunder or when the unit is not used for prolonged periods. [. . . ] 3 Replace the cover. 2 Position two batteries of the type AAA/R03/UM4 in the battery compartment. Make sure that the orientation of the batteries is correct (see drawing at bottom). - Do not mix new and old batteries and do not use different types of batteries. - If the remote control is not used for prolonged periods, remove the batteries from the remote control to avoid corrosion. Using the remote control Direct the remote control at the sensor on the front panel of the unit. When the remote control signal is received, the unit reacts accordingly. The remote control works within a range of 6 metres. CDP-200 CD-PLAYER DIGITAL AUDIO STANDBY / ON REWIND FORWARD POWER 1 2 3 4 5 6 7 8 9 AUTOTUNE 0 ST/MO 10+ MEMORY DISPLAY CD DVD TUNER T MODE AUX1 AUX2 AUX3 PHONO STATION STATION ENTER TUNING TUNING AUDIO SETUP MENU VOLUME SUBTITLE TITLE MUTE REPEAT RANDOM SLOW HIFI-200 - Sometimes the remote control does not work well in strong light. Malfunction may occur if other remote controls are used near the unit. Do not place any objects on the remote control, as the batteries may become flat if a key is depressed constantly. Make sure that there are no obstacles between remote control and unit. Do not position the unit behind tinted glass as it may reduce the maximum range of the remote control. 09 REMOTE CONTROL Remote control functions POWER 1 8 1 1 2 3 4 2 3 2 5 6 7 8 9 AUTOTUNE 0 ST/MO 10+ MEMORY DISPLAY 9 10 4 5 6 7 8 9 CD DVD TUNER T MODE 11 3 AUX1 AUX2 AUX3 PHONO STATION STATION ENTER 12 TUNING 10 11 12 13 14 TUNING AUDIO SETUP MENU VOLUME SUBTITLE TITLE MUTE 4 5 6 7 REPEAT RANDOM SLOW System off: Sets all devices in the hifi 200 series into standby 0-9 Digits: Selects tracks on the CDP-200. CD: Turns the CDP- and AMP-200 on and selects the CD input on the AMP-200. The DVD, TUNER, AUX1, AUX2, AUX3 and PHONO buttons will set the CDP-200 into standby. Random: All tracks on the disc loaded in CDP-200 are played in random order. Repeat: Repeats a single track or all tracks on a disc on CDP-200 Previous/Fast reverse: Selects the previous track on CDP-200. Press and hold to rewind playback Stop: Stops playback on CDP-200 Eject: Opens and closes the disc tray on the CDP-200 +10: Use this button along with the 0-9 digits to select tracks on the CDP-200 above 10. For example press the +10 button and the 5 digit to select track 15 on a disc. Display: Canges between showing the time of Track Elapsed, Track Remain and Disc Remain on the display Memory: Use this button to set the playback order to a prefered order. Press and hold to fast forward playback 13 14 HIFI-200 Some of the functions of the unit can only be performed by means of the remote control. Note that the accessories in the pictures on this page are not included in the supply. 13 OPERATION AND FUNCTIONS On, Off and standby 1 Turn on the unit by pressing the mains switch on the rear panel. Then press the CD button on the remote, or the standby button on the front panel. 2 Press the standby button on the remote control to switch into standby mode. The display will turn off and all functions will be reduced to a minimum to make sure that the unit uses minimal power. When in standby mode the unit only reacts to the CD button of the remote control(3). [. . . ] If you press the button once, one track will be repeated and the display will show REP 1. If you press the button twice, all tracks will be repeated and the the display will show REP ALL If you wish to deactivate the repeat function, press the REPEAT button for a third time. Note: This function can also be used when "MEMORY" has been activated. CD Rep 1 02 04 : 26 CD Rep all 02 04 : 26 17 TROUBLESHOOTING Troubleshooting PROBLEM No power when unit is turned on. CAUSE/REMEDY - Switch on the electric current at the socket. - The internal fuse has blown and must be replaced by a qualified service technician. [. . . ]