User manual SYMPHONIC TVCR19E1

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] BRIGHT CONTRAST COLOR TINT SHARPNESS BRIGHT ­PPPPPPPCPPPPPPP+ 3 Adjust sound Press VOLUME(VOL. ) X or Y to adjust the volume. VOLUME 20 3 C CC C C C CCCCCCCCCC Adjust the picture control NOTE: · If you press the CHANNEL(CH. ) o or p in the DVD mode, you can change the TV channels. Even if you turn off the TV/DVD in the DVD mode, when you turn it on again, it will go into the TV mode. Press B or s to adjust to your desired level within 5 seconds. NOTE: · At step 3, the picture adjustment display will disappear from the TV screen after about 5 seconds unless you press any buttons, even though you may not be finished. In this case, repeat from step [1]. DEGAUSSING Magnetism from nearby appliances and speakers might affect the color of the TV picture. If the color is still not correct, disconnect power cord from AC outlet then reconnect it after 30 minutes. BRIGHT CONTRAST COLOR TINT SHARPNESS s to decrease brightness to decrease contrast to pale to purple to soft B to increase brightness to increase contrast to brilliant to green to clear · If there is a power failure of any kind, the unit will retain its memory for this feature. ­ 15 ­ EN 0C28 SLEEP TIMER TV The Sleep Timer function enables you to shut off the power without pressing POWER after a desired time period. NOTE: If the TV/DVD displays a black box on the TV screen, this means that the TV/DVD is set to the TEXT mode. · TV/DVD power must be turned on. 1 Set "SLEEP TIMER" Press SLEEP on the remote control. You may change the sleep time with pressing SLEEP on the remote control repeatedly. The timer is set up to 120 minutes, 30 minutes each time SLEEP is pressed. SLEEP 120 MINUTE 1 Select "CAPTION" - TV SETUP - To cancel the sleep timer: Press SLEEP repeatedly until "SLEEP 0 MINUTE" is displayed. NOTES: · When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost. · To view the time left for sleep timer press SLEEP once when SLEEP display disappears. After 10 seconds, display will disappear again. Press SETUP on the remote control. If you select the rating category (example: TV-PG) and turn it [BLOCK] or [VIEW], the sub-ratings (example: V for Violence) will turn [BLOCK] or [VIEW] automatically. You can set the sub-ratings to [BLOCK] or [VIEW] individually when the rating category is set to [BLOCK]. · When you select [TV-Y7]: Press L or K to select "FV" (Fantasy Violence). · When you select [TV-PG], [TV-14] or [TV-MA]: Press L or K to select "D"(Suggestive Dialog), "L"(Coarse Language), "S"(Sexual Situation), or "V"(Violence). NOTE: When you select [TV-MA], "D" does not appear on the TV screen. · The sub-ratings which set to [BLOCK] appears next to the rating category in the TV RATING menu. TV­Y7 [BLOCK] B FV [BLOCK] TV­PG [BLOCK] BD L S V [BLOCK] [BLOCK] [BLOCK] [BLOCK] B TV­Y TV­Y7 ( ) TV­G TV­PG (DLSV ) TV­14 (DLSV ) TV­MA ( LSV ) [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] Press K or L to point to your desired item. Then, press ENTER to select [BLOCK] or [VIEW]. 5 Exit the V-Chip setting mode Press SETUP on the remote control to return to original mode. ­ 17 ­ EN 0C28 MPAA RATING SET UP Make sure . . . · TV/DVD power must be turned on. CHANGE ACCESS CODE To change access code, follow the steps. 1 1 Select "V-CHIP SET UP" - TV SETUP CHANNEL SET UP B V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] Select "V-CHIP SET UP" - TV SETUP CHANNEL SET UP B V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] Press SETUP on the remote control. Then, press ENTER. 2 Enter 4-digit access code ACCESS CODE 2 Enter 4-digit access code ACCESS CODE Press Number on the remote control. The default code is 0000. ____ Press Number on the remote control. The default code is 0000. ____ 3 Select "MPAA RATING" ­ V-CHIP SET UP ­ TV RATING B MPAA RATING CHANGE CODE 3 Select "CHANGE CODE" ­ V-CHIP SET UP ­ TV RATING MPAA RATING B CHANGE CODE Press K or L to point to "MPAA RATING". [. . . ] No CD reproduction DVD picture dropout DVD picture freeze DVD picture in mosaic No DVD reproduction No picture. NOTES: · Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner's Manual for details on correct operations. · Playback from a desired track and random playback are not available during program playback. [. . . ]