User manual SUUNTO VECTOR HR

[. . . ] EN USERS GUIDE [MODE] TIME [SELECT] [SELECT] [MODE] ALTIMETER [SELECT] [MODE] BAROMETER [SELECT] [MODE] COMPASS [SELECT] [SELECT] DECLINATION ADJUSTMENT [SELECT] COMPASS CALIBRATION [MODE] HEART RATE MONITOR [SELECT] [MODE] DAILY ALARMS [SELECT] DIFFERENCE MEASUREMENT [SELECT] [SELECT] [SELECT] [MODE] 24 HOUR MEMORY [SELECT] DIFFERENCE MEASUREMENT [MODE] [SELECT] 4 DAY MEMORY [SELECT] SEA LEVEL PRESSURE [MODE] STOPWATCH [SELECT] [SELECT] INTERVAL TIMER [SELECT] [MODE] DUAL TIME LOGBOOK [SELECT] LOGBOOK HISTORY MEMORY USER'S GUIDE CUSTOMER SERVICE CONTACTS Suunto Oy Suunto USA Canada European Call Center Suunto Website Phone +358 9 875870 Fax +358 9 87587301 Phone 1 (800) 543-9124 Phone 1 (800) 267-7506 Phone +358 2 284 11 60 www. suunto. com EN Table of ConTenTs CHaPTeR 1 InTRoduCTIon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General InformatIon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . maIn functIons (moDes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . Water resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . [. . . ] note: If the user does not press any button for 1 minute in the setup mode, the display will automatically exit setup. setting the time is now complete. 3. 2 daIly alaRM sub Mode In the Daily Alarm mode (Fig. 19): · · · the Daily alarm sub mode allows the user to select and set up to 3 alarms. In the tIme mode, press the [select] button once to enter this sub mode. field displays "on" or "off" (the activation status of a particular alarm), field displays the time of a particular alarm, and field 3 displays the alarm (, , or 3) the user is viewing. pressing the [+] or the [-] button will toggle between the alarms , , or 3 to view the settings for each alarm. 3. 2. 1 How to set the daily alarms . press the [+] or the [-] button to select the desired alarm to be set (, , or 3). Located in Field 1, the "ON" or "OFF" will begin to flash. press either the [+] or the [-] button to toggle between "on" and "off". at the setting desired, press the [select] button to move to the next setting. press the [+] button to scroll the hour upward or press the [-] button to scroll the hour downward. at the hour desired, press the [select] button to move to the next setting. press the [+] button to scroll the minutes upward or press the [-] button to scroll the minutes downward. at the minutes desired, press the [mode] button to accept the changes and exit the setup program. a small bell will appear at the bottom left side in field to signify an alarm has been activated. to activate up to three alarms, please repeat steps -8 for the selected alarm (, , or 3). 5 3. 3 dual TIMe sub Mode In the dual time mode (Fig. 20): · · · field displays "dua" indicating "dual time", field displays the current time, and field 3 displays the dual time (e. g. your home time). the Dual time sub mode allows you to set the watch to display a time other than the main one. In the tIme mode, press the [select] button twice to enter this sub mode. the user can display the seconds while in this sub mode by pressing the [+] button, in field 3 the seconds will appear for 0 seconds. afterwards the display returns to showing the dual time. 3. 3. 1 setting the dual Time function In the dual time mode: 1. press the [+] button to scroll the hours upward or press the [-] button to scroll the hours downward. at the hour desired, press the [select] button to move to the next setting. located in field 3 to the right of the hour value, the minutes will begin to flash. [. . . ] lower point set reference altitude (real altitude) Displayed altitude real outside temperature normal (table) temperature temperature offset (= real - normal) sum of temperature offsets table 2. example using meters and celsius +7. 5 ºc +8. 5 ºc +9 ºc +9 ºc + + ºc = 0 ºc 000 m 3000 m +6. 5 ºc -4. 5 ºc + ºc Higher point 50 table 3 shows an example in which the temperature offsets are negative. at 9840 feet the altitude difference is 6560 feet and Wristop computer shows 00 feet too much (-4 ºf * 6560 ft * 0. 00/ºf = -00 ft). lower point set reference altitude (real altitude) Displayed altitude real outside temperature normal (table) temperature temperature difference (= real - normal) sum of temperature offsets table 3. [. . . ]