User manual SUUNTO CORE

[. . . ] en USER GUIDE MODES AND VIEWS TIME · date · seconds · dual time · sunrise and sunset times · stopwatch · countdown timer · empty COMPASS · time · cardinals · bearing tracking ALTI & BARO altimeter barometer depth meter · log recorder · log height difference · log ascent · log descent · altitude difference measurer · temperature · empty · temperature · log recorder · altitude reference · time · empty · log recorder · temperature · time MENU CONTENT SYMBOLS ON THE DISPLAY 1 Welcome . . 19 19 20 20 22 22 23 24 26 27 28 29 30 31 31 31 34 35 36 36 39 39 39 40 41 3 en 7. 3 Choosing recording interval . 49 4 1 WELCOME "For over 70 years Suunto has provided accurate, reliable information to people in need of it. Our instruments enable our users to reach their goals more effectively and get more out of their sports experience. [. . . ] You want to be able to check your progress as you climb, so you activate the altitude difference measurer on your Suunto Core. You start climbing, checking your altitude occasionally to see how far you are from the next check point. You check your altitude, and see that there's still a lot of climbing ahead. Maybe you need to rethink your next check point. 5. 5. 2 Recording logs The log recorder stores all your movements in altitude between the start and stop times. If you are engaged in an activity in which your altitude changes, you can record the altitude changes and view the stored information later. You can also set altitude marks (laps), allowing you to view the duration and ascent/descent height between your previous mark and current mark. Keep [+] pressed to reset (this can only be done when the recorder is stopped). Log height difference: shows the measured altitude difference between a log starting point and a log finishing point with the following icons: In the additional views: is displayed when your altitude is above the starting point. 24 is displayed when your altitude is the same as at the starting point. is displayed when you view how much you have ascended from the log start. is displayed when you view how much you have descended from the log start. Altitude points are recorded according to the recording interval you have chosen (see Section 7. 3 Choosing recording interval on page 41). NOTE: An estimation of how much time you can record is shown in the lower part of the display when you browse between the recording rates. The actual recording durations may vary slightly depending on your activity during the recording period. You can access your history of recorded logs, including log details, from LOGBOOK in MENU (see Section 7. 2 Viewing and locking logs on page 39). TIP: When you have stopped the log recorder, you can enter the logbook and view your current recordings before you reset the recorder. en 25 Possible real life situation: Recording altitude You're going on another mountain hike. This time you want to record how much you ascend and descend so as to compare the figures with previous hikes. You set your Suunto Core to the ALTIMETER profile and start the log recorder when you begin the hike. Now you can compare it with your previous logs. 5. 6 Using barometer profile The BAROMETER profile shows the current sea level air pressure. This is based on the reference values given and the constantly measured absolute air pressure. Changes in sea level air pressure are presented graphically in the middle of the display. The display shows the recording of the last 24 hours with a recording interval of 30 minutes. When the BAROMETER profile is activated, the word BARO is underlined on the display. When the BAROMETER profile is activated, you can access the following views with [View]: Temperature: measures the current temperature Log recorder: records the altitude changes in logs 26 Altitude reference: shows the altitude reference value Time: shows the current time Empty: no additional view NOTE: If you are wearing your Suunto Core on your wrist, you will need to take it off in order to get an accurate temperature reading because your body temperature will affect the initial reading. [. . . ] NOTE: When scrolling the graph, your current position is in the middle of the graph. 40 NOTE: Only altimeter logs include summaries. en 7. 2. 2 Locking and unlocking logs To lock or unlock logs: 1. Lock/unlock the log with [Mode] OR Cancel with [View]. 7. 3 Choosing recording interval You can choose the recording interval in REC INTERVAL in MENU. You can choose between five recording intervals: 1 second 5 seconds 10 seconds 30 seconds 60 seconds When browsing through the intervals, the available recording time is shown in the lower part of the display. [. . . ]