User manual SUREHEAT FSR38

[. . . ] Z223. l-l 998 and the National Electrical Code ANSI/NFPA No. 70-- 1)0 N0'l' store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other app1iancc. \%ARNING DO NO'I' try lighting this appliance without reading the "I. IGHTING INSTRUCTIONS" section of this manual Grill Assembly . IMPORTANT: Remove all protective plastic film from stainless steel parts prior to assembly/use. This film is installed at the factory to prevent damage that could occur during shipment and handling. LEFT SHELF ASSEMBLY 1. Open the grill hood and place a piece of Styrofoam from the packaging under the grill hood to prop the grill hood open slightly. Attach the left shelf by inserting the four shelf hooks into the slots on the side of the grill. [. . . ] Department of Transportation (DOT) or the National Standard of Canada, CANICAS-Bssg, Cylinders, Spheres and 1ube~ for the Transportation of Dangerous Goods. " L. P. tank on, make sure to open the valve SLOWLY two (2) complete turns to insure proper gas flow. Most gas tanks now come equipped with a leak detector mechanism Internal to the tank, when gas Is allowed to escape rapidly it shuts oil the gas supply. Opening the valve rapidly may simulate a gas leak, causing the safety device to activate, restricting gas flow causing low flames. Opening the valve slowly will insure this safety feature is not falsely triggered. · When not in use, gas supply cylinder valve is to be in the `OFF" position. · The tank supply system must be stored upright to allow for vapor withdrawal, · The regulator and hose assembly must be inspected before each use of the grill. If there is excessive abrasion or wear or If the hose is cut, it must be replaced prior to the grill being used again. `Cylinders must be stored outdoors out of the reach of children and must not be stored in a building, garage or any other enclosed area. gas cylinder under or near the grill. Pre Operation Leak Testing GENFRAI INFORMATION Although all gas connections on the grill are leak tested prior to shipment, a complete gas tightness check must be performed at the installation site due to possible shifting during shipment, installation or excessive pressure unknowingly being applied to the unit. Periodically chock the whole system for leaks arid immediately check the system it the smell of gas is detected. Do not smoke while leak testing. Mix a solution of equal parts mild detergent or liquid soap and water TESTING 1. Turn the top knob of the fuel supply cylinder counterclockwise (right to left) two (2) rotations to open. 8 3. Apply the soap solution to connections of the fuel supply assembly. If a leak is detected, immediately turn off the gas supply, tighten any leaking fittings, turn gas on, and repeat steps 1-3. Turn on the burner control knobs for a moment to release the pressure in the hose, then turn the control knobs back off. Wash off soapy solution with cold water and towel dry. Check all gas supply fittings before each use and each time the gas supply cylinder is connected to the regulator. Have a qualified service technician leak test the grill any time a part of the gas system Is replaced. Also it is recommended to perform a leak test at least once a year whether or not the L. . P. NOTE: When leak testing this appliance, make sure to test and tighten all loose connections, Including the side burner A slight leak In the system can result in a low flame, or hazardous condition. Most LPL gas tanks now come equipped with a leak detector mechanism internal to the tank, when gas Is allowed to escape rapidly, it shuts off the gas supply. A leak may significantly reduce the gas flow making the grill difficult to light or causing low flames. NOTE: If you cannot stop a gas leak turn of-f the gas supply and call your local gas or the dealer you purchased the appliance from. [. . . ] We recommend you chock the grill and remove any spiders, insects and webs at least once a year to reduce this risk. 9 BEFORE CALLING CUSTOMER SERVICE If the grill does not function properly, use the following checklist. PROBLEM - SOLUTION Grill will not light when the igniter button is pushed. Note You will need to remove your cooking grates and flavor grids to see the electrodes. - Check to see if your igniter battery is installed correctly with the positive side first. Check for loose wire connections to the igniter or electrodes Check to see if debris is blocking the electrodes. If the igniter Is not working can you light the grill with a match? Warranty LIMITED LIFETIME WARRANTY Sanama warrants this grill to the original purchaser of our grills when subject to normal residential use to be free from defects in workmanship and materials for the periods listed below. [. . . ]