User manual SUPERMICRO RSC-R2UU-A4E8

[. . . ] IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not copy any part of this document. [. . . ] The connector with twisted wires always connects to drive A, and the connector that does not have twisted wires always connects to drive B. Table 2-29 Parallel (Printer) Port Pin Definitions (J16) Parallel Port Connector (370DE6/370DER only) The parallel port is located on J16. See Table 2-29 for pin definitions. Pin Number 1 3 5 7 9 11 13 15 17 19 21 23 25 Function Pin Number Function Strobe2 Auto FeedData Bit 0 4 ErrorData Bit 1 6 InitData Bit 2 8 SLCT INData Bit 3 10 GND Data Bit 4 12 GND Data Bit 5 14 GND Data Bit 6 16 GND Data Bit 7 18 GND ACK 20 GND BUSY 22 GND PE 24 GND SLCT 26 NC 2-17 Installation SUPER 370DE6/370DER/370DEI User's Manual Floppy Connector The floppy connector is located on J15. See Table 2-30 for pin definitions. Table 2-30 Floppy Connector Pin Definitions (JP15) Pin Number 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 Function GND GND Key GND GND GND GND GND GND GND GND GND GND GND GND GND GND Pin Number Function 2 FDHDIN 4 Reserved 6 FDEDIN 8 Index10 Motor Enable 12 Drive Select B14 Drive Select A16 Motor Enable 18 DIR20 STEP22 Write Data24 Write Gate26 Track 0028 Write Protect30 Read Data32 Side 1 Select34 Diskette Installation IDE Connectors There are no jumpers to configure the onboard IDE connectors J13 and J14. Refer to Table 2-31 for pin definitions. Pin Number 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Table 2-31 IDE Connector Pin Definitions (J13, J14) Function Reset IDE Host Data 7 Host Data 6 Host Data 5 Host Data 4 Host Data 3 Host Data 2 Host Data 1 Host Data 0 GND DRQ3 I/O WriteI/O ReadIOCHRDY DACK3IRQ14 Addr 1 Addr 0 Chip Select 0 Activity Pin Number 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Function GND Host Data 8 Host Data 9 Host Data 10 Host Data 11 Host Data 12 Host Data 13 Host Data 14 Host Data 15 Key GND GND GND BALE GND IOCS16GND Addr 2 Chip Select 1GND 2-18 Chapter 2: Installation Ultra160 SCSI Connector (not on 370DEI) Refer to Table 2-32 for pin definitions for the Ultra160 SCSI connectors located at JA1, JA3 and JA5. JA5 is a connector for external SCSI drives and is included only on the 370DER+. Table 2-32 68-pin Ultra160 SCSI Connectors (JA1, JA3, JA5) Connector Contact Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Signal Names +DB(12) +DB(13) +DB(14) +DB(15) +DB(P1) +DB(0) +DB(1) +DB(2) +DB(3) +DB(4) +DB(5) +DB(6) +DB(7) +DB(P) GROUND DIFFSENS TERMPWR TERMPWR RESERVED GROUND +ATN GROUND +BSY +ACK +RST +MSG +SEL +C/D +REQ +I/O +DB(8) +DB(9) +DB(10) +DB(11) Connector Contact Number 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 Signal Names -DB(12) -DB(13) -DB(14) -DB(15) -DB(P1) -DB(0) -DB(1) -DB(2) -DB(3) -DB(4) -DB(5) -DB(6) -DB(7) -DB(P) GROUND GROUND TERMPWR TERMPWR RESERVED GROUND -ATN GROUND -BSY -ACK -RST -MSG -SEL -C/D -REQ -I/O -DB(8) -DB(9) -DB(10) -DB(11) 2-19 Installation SUPER 370DE6/370DER/370DEI User's Manual 2-9 Installing Software Drivers After all the hardware has been installed you must install the software drivers. The necessary drivers are all included on the Supermicro CD that came packaged with your motherboard. After inserting this CD into your CDROM drive, the display shown in Figure 2-5 should appear. (If this display does not appear, click on the My Computer icon and then on the icon representing your CDROM drive. Finally, double click on the S "Setup" icon. ) Installation Figure 2-5. Driver/Tool Installation Display Screen Click the icons showing a hand writing on paper to view the readme files for each item. The bottom icon with a CD on it allows you to view the entire contents of the CD. Build SCA disk (QLogic GEM 354): For integration with the SuperServer SC850 and SC860 chassis. We can be reached by e-mail at support@supermicro. com or by fax at: (408) 503-8000, option 2. Troubleshooting http://www. supermicro. com/techsupport/contact_support. htm. 3-3 Frequently Asked Questions Question: What are the various types of memory that the 370DE6/ 370DER motherboard can support?Answer: The370DE6/370DER/370DEI has four DIMM slots that support 168pin, registered ECC DIMMs ECC only. PC133 and PC100 memory are both fully supported at their respective speeds. Important: The memory employs a two-way interleaving scheme, which requires you to install memory modules in pairs (-first in the two slots of Bank0, and then, in both slots of Bank1, if needed. ) Question: How do I update my BIOS?Answer: It is recommended that you do not upgrade your BIOS if you are experiencing no problems with your system. Updated BIOS files are located on our web site at http://www. supermicro. com. Please check our BIOS warning message and the info on how to update your BIOS on our web site. Also, check the current BIOS revision and make sure it is newer than 3-3 SUPER 370DE6/370DER/370DEI User's Manual your BIOS before downloading. Select your motherboard model and download the BIOS file to your computer. Unzip the BIOS update file and you will find the readme. txt (flash instructions), the fwhflash. com (BIOS flash utility) and the BIOS image (xxxxxx. rom) files. It is not necessary to set BIOS boot block protection jumpers on the motherboard. [. . . ] Determining the amount of memory above 1 MB memory next. APPENDIX B B-4 Appendix B: AMIBIOS POST Diagnostic Error Messages Checkpoint Code Description 4Bh The amount of memory above 1 MB has been found and verified. Checking for a soft reset and clearing the memory below 1 MB for the soft reset next. Adjusting the displayed memory size for relocation and shadowing next. 51h The memory size display was adjusted for relocation and shadowing. [. . . ]