User manual STRONG SRT ANT 45

[. . . ] Mobilfunknetze NL support_nl@strong. tv 801 702 017 PL support_pl@strong. tv +380(44)228 24 73 UA support_ua@strong. tv DK support_dk@strong. tv 29 Aug 2014 18:06 Supplied by STRONG & Co, Japan Represented by STRONG Ges. m. b. H. Franz-Josefs-Kai 1 1010 Vienna Austria Email: support_at@strong. tv PART 1 Table of Contents 1. 0 Introduction 2. 0 Package contents 3. 0 Safety notes 4. 0 Connecting the antenna 5. 0 Installation of the antenna 1 2 2 3 5 English 1. 0 Introduction Thank you for purchasing the STRONG SRT ANT 45 DVB-T/T2 antenna. This antenna has been specially designed to receive digital terrestrial signals. [. . . ] Always check voltages and polarisation of the adaptor before connecting it. 2 PART 1 4. 0 Connecting the antenna Preparations 1. Check if the broadcast in your country is horizontally or vertically polarised. 2. Fix the antenna to the multi-directional base as shown in the pictures: 3. Depending on how the signals are broadcasted (horizontally or vertically) you will have to mount your antenna in the horizontal or vertical position for best performance. Check in the menu or user manual of your terrestrial receiver to see if it supports the needed 5 V power. 3 English H V „„ (Vertical-Broadcast) antenna mounted V: „„ (Horizontal-Broadcast) antenna mounted H: 4. 1 To power the antenna with Digital Terrestrial Receiver 1. Turn on your TV set and turn on your Digital Terrestrial Receiver. 2. Press the “MENU” button on the remote control of your Digital Terrestrial Receiver. Check in the Set-Up or Installation menu of your receiver to see if the antenna power is set to “ON”. (Normally this is indicated in the menu as ANT power, Ext Antenna power or Active antenna power. ) Refer to the user manual of your Digital Terrestrial Receiver. 3. Once you are sure that your receiver supports 5 V antenna power, switch off your receiver and disconnect it from the 230 V main power. 4. Take the supplied “long” coaxial cable and connect the end with the “F connector” (screw type connector) to the antenna. Carefully press the inner lead of the cable into the Female-F connector at the back of the antenna. Normally the input connector on your receiver is marked as “ANT” (in) or as “RF” (in). 6. Connect your receiver to the 230 V main power and switch ON your receiver and TV set. 4. HDMI or SCART cable (optional) 5. Coaxial cable 6. Water-Drop Loop (recommended) 4 2 5 6 If your receiver does not support 5 V antenna power, then please follow the next steps: 4. 2 To power the antenna with external power adaptor 1. Switch OFF your receiver and disconnect it from the 230 V mains power. 2. Take the short coaxial (IEC Male to IEC Female) cable. Normally the input connector on your receiver is marked as “ANT” (in) or as “RF” (in). 3. Connect the other end of the cable to the connector on the power injector that is marked as “Receiver”. 4. Take the supplied “long” coaxial cable and connect the end with the “F connector” (screw type connector) to the antenna. Carefully press the inner lead of the cable into the Female-F connector at the back of the antenna. 5. Connect the other side of the cable to the connector at the power injector, it is marked as “Antenna”. [. . . ] Slowly move the antenna to different positions around the house, at the same time monitor the signal bars in the menu, once the signal indicator shows the maximum signal, fix the antenna on that position. Note  is recommended NOT to place the antenna near to: It „„ Devices that are strong source of radiation or interference such as DECT and GSM telephones, transmitters, microwaves, Wi-Fi, etc. „„ Devices with high power consumption such as electrical heater, air conditioner, hairdryers, etc. Once the best position for the antenna has been found it can be mounted and fixed in that place. [. . . ]